AdBlock Warning

Parts of this website do not function properly with AdBlock enabled on your device. To get the best user experience on our website, please disable Adblock for this website (domain) on your browser.


Aiden Firth

Members via FB
  • Content count

    137
  • Joined

  • Last visited

  • Days Won

    9

Aiden Firth last won the day on July 1 2015

Aiden Firth had the most liked content!

Community Reputation

44 Excellent Reputation

About Aiden Firth

  • Rank
    Advanced Member

Profile Information

  • Gender*
    Male
  • Toyota Model
    Aurion SX6
  • Toyota Year
    2010
  • Location
    Queensland
  • Annual Mileage
    0 to 5000

Recent Profile Visitors

8,447 profile views
  1. Pictures of lowered Aurions.

    Not the best pics, but you get a rough understanding of height. I also had lows which were the only ones that were available at that time.
  2. Can't get a replacement VVTI Oil line?

    The new part they put in is the solid pipe, would be pretty stupid to put back in a rubber one. They have parts in stock but they are for ones that come in leaking. They are waiting for parts from Japan
  3. I want to go LOW

    I also had a set of the slide industries coilovers, i had a set of BCs before that which wernt too bad. The slides had decent spring rates so you can put bigger and wider wheels on with minimal scrubbing. Coilovers would be the way to go if you want to go low.
  4. Park Brake

    If you get a set of vernier calipers, the measurement on the outside of the shoes is 189.7mm, set it to that and it should be pretty good
  5. Park Brake

    the cable adjuster is located next to the park brake, you will need a 10mm spanner and a 10mm deep socket to adjust it
  6. K&n filter for 2015 aurion

    Not really worth installing a panel filter, unless you get a short ram or a cold air intake, even then, there is next to no power gains but the intake noise sounds kinda good
  7. Tyres

    you should be good for the front, but you will scrub hard on the rear without "modifying" thingsI had 19x9.5 +37 all round and i had to make the rears fit
  8. 2011 Aurion sportivo front bumper scrape

    did you lower it with lowered springs or coilovers?
  9. Wheel fitment

    I had 19x9.5 +37 all round, if you lower your car you will need to roll guards. But the wheels will sit out of the guards if at stock height (due to no natural camber) I had to "modify" things to stop it from scrubbing at the height i was at. I had 245/35 tyres, if i did it again i would get a smaller tyre size
  10. 100,000km Service - General Question

    You should've also got the spark plugs last service. Also the clunk would be from the parking paw coming off the park gear, if your handbrake is no good then some of the vehicle weight will be taken up by it.
  11. Nothing to worry about, there are cars that come into my work like this all the time. My Aurion was alot worse than this as it was pretty low :)
  12. Blast From The Past!

    :O how dare you. Hahaha :PThey are a superb car to drive
  13. Aurion intermediate shaft spline

    yes, that is very excessive, if you do the job correct, it shouldnt need a wheel alignment(thats also a expensive wheel alignment, the place i work at charge $69 for a full W/A), as for the labour, it only takes not even 30 mins to do it so i don't know where they got that price from
  14. Aurion intermediate shaft spline

    why did it cost so much? Surely they could'nt have charged $500 labour,,it only takes like half an hour to do it if that.
  15. 2011 Aurion sportivo front bumper scrape

    Hope you guys never lower your cars lol The key is to angle it up the driveway, not go straight for it like i see most people do