Jump to content

Front Door Lock Actuators

Maddad

By Maddad
in Camry Club

 Share

Recommended Posts

Maddad Progessing

Maddad

Posted
Posted

Hi

I have Toyota Camry Sedan Auto 1996. The alarm system sounds when the remote is used to lock the car. When locked its ok for about 3-4 seconds and then sounds. I have tracked it down to the left front door actuator. It seems that the mechinism in the door is not pulling the rod far enough to lock and the security system sees this as an unlock condition and it goes off.

I have pulled the actuator out and the levers in this thing have a lot of muck like hard grease etc. The reason for this post is to see if anyone has any experience at fixing them so I can get a bit of an idea on repairing it. Is it a common thing. Any ideas would be much apprieciated.

I have not priced out a new one, but I'll bet its worth a fortune.

Thanks

Link to comment
Share on other sites
Rolla & Sao Boy Mentor

Rolla & Sao Boy

Posted
Posted

Hi

I have Toyota Camry Sedan Auto 1996. The alarm system sounds when the remote is used to lock the car. When locked its ok for about 3-4 seconds and then sounds. I have tracked it down to the left front door actuator. It seems that the mechinism in the door is not pulling the rod far enough to lock and the security system sees this as an unlock condition and it goes off.

I have pulled the actuator out and the levers in this thing have a lot of muck like hard grease etc. The reason for this post is to see if anyone has any experience at fixing them so I can get a bit of an idea on repairing it. Is it a common thing. Any ideas would be much apprieciated.

I have not priced out a new one, but I'll bet its worth a fortune.

Thanks

I know you have mentioned that you think the fault is "left front door actuator" , have you tested it to confirm though ?

Disable that door/left front door actuator so it doesnt trigger when the alarm is engaged and then see if it goes off ..

I havent had that problem but to replace the motor just go to supercheap or autobarn and they sell the actuator on it own.

Worst case you might have to buy a 2 door central looking kit $30 odd dollars or Ebay has some deals too..

Dont worry its not too costly , you have done the hard work of taking the trim off and getting to the base of it all , if anything that would have cost you Mega $ if you took it Toyota or some other repair place .. wink.gif

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing



  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 2

      Muffler change for zr6

      Whats with those small links?
      Baxter190388 in Aurion / TRD Aurion Club
    2. 1

      Brake issues

      BTW forgot to mention that there is no shake in the steering wheel. The 'shudder', really hard to describe but almost like brakes on and off. Cannot identify front or rear or both. Got me totally miffed.
      larry200 in Landcruiser
    3. 1

      Brake issues

      Hi everyone, new to this forum - refugee from LCOOL. Had a minor shudder when applying the brakes. Also was somewhat intermittent. Having over 100k on the clock a lot which were done towing a big van, I thought I may have warped a disk. Checked them with a dial gauge but no useful info. Bit the bullet and replaced all 4 with new slotted rotors and pads from DBA. Huge difference in braking. However the shudder has return almost with a vengeance. Thought I fixed the problem when I disconnected the ECU for another unrelated issue. ECU is remapped, car went in limp mode and could not clear it with the scangauge. Problem not fixed and I am lost as to why this is happening. Plan on visiting Berima Diesel later on this year to have the injectors checked and I'll get them to look at the brakes if I still haven't figured it out. Any suggestions would be welcomed. Thank you
      larry200 in Landcruiser
    4. 1

      Hi, I'm Magazi in NSW I'm a new member

      G’day and Welcome Maga I’m new here so Sorry can’t help but thought I’d say 👋
      Sparky600 in New Members Introductions
    5. 2

      Muffler change for zr6

      To my knowledge depending on the year off npp exhaust it's already done factory. snaptube vidmate
      ablaeh in Aurion / TRD Aurion Club
    6. 2

      IAC for 1997 Camry Vienta (3vzfe)

      Ah I see, I had no idea aisan was related to toyota. I initially thought it was clone of aisin or smth
      ASHX in Camry Club
    7. 26

      200 series won’t shift past 4th gear

      Hi everyone, new to this forum - refugee from LCOOL. Having read some of the replies, to the best of my knowledge there is no such thing as a minor remap. Toyota in their wisdom have the software in the ECU such that it cannot be downloaded, modified and reloaded. It has to be a complete reload, either stock or modified. All you fellows disconnecting the battery is a good and simple way to try and reset everything but similar results can be achieved by simply disconnecting the ECU. That's the big plug in the firewall passenger side. Meanwhile I may need to start a new topic for the following issues I am experiencing: Had a minor shudder when applying the brakes. Also was somewhat intermittent. Having over 100k on the clock a lot which were done towing a big van, I thought I may have warped a disk. Checked them with a dial gauge but no useful info. Bit the bullet and replaced all 4 with new slotted rotors and pads from DBA. Huge difference in braking. However the shudder has return almost with a vengeance. Thought I fixed the problem when I disconnected the ECU for another unrelated issue. ECU is remapped, car went in limp mode and could not clear it with the scangauge. Problem not fixed and I am lost as to why this is happening. Plan on visiting Berima Diesel later on this year to have the injectors checked and I'll get them to look at the brakes if I still haven't figured it out. Any suggestions would be welcomed. Thank you
      larry200 in Landcruiser
    8. 7

      which engine oil

      I been using nulon w5-30 fully synthetic long life and good on fuel change oil every 5000kms to keep it clean all d time
      alan de Leon in Kluger
    9. 0

      G’day from NSW

      G’day All just got a 2012 (old shape) Corolla Ascent Hatchback Auto. Needs a few things done, it was my Dads who just passed away. Going to install pioneer head unit (basic one really) as a start, then maybe upgrade speakers but I’ll see how the oem ones go, I’ve read I’ll need at least 50w ones for the pioneer. Front inner plastic guards are a bit trashed along with bumper bar, just need to neaten it up a little. cheers Sparky
      Sparky600 in New Members Introductions
    10. 3

      Head Unit Replacement for 2010 Toyota Corolla Hatch

      G’day TGA, hope you got this sorted, just about any 2 din would fit. I’m putting a pioneer one in but I’d like to know how to pull the trims apart to fit it 🤨 Every video shows the sedan with a different gearshift with short trims to remove but those 2 lower side ones are 1 piece on the hatch and I’m struggling. Do I need to remove console box to start removing those side piece. Any help cheers Sparky
      Sparky600 in Corolla / Corolla Sportivo Club
×
×
  • Create New...

Forums

News

Membership