Jump to content

Sound from the rear sway bar`

KT_haha

By KT_haha
in Corolla / Corolla Sportivo Club

 Share

Recommended Posts

KT_haha Mentor

KT_haha

Posted
Posted

I replaced my rear sway bar a week ago with the whiteline one, handling is all different and I love it :D

The day after the replacement, we had the Natio run with the boys from the forum (it was supposed to be the Cross City tunnel break in), the run was kinda bumpy and after that, the rear sway bar started to have this "konk konk" sound when ever the body twists. So I took it back to the workshop and asked them to tighten it which fixed the problem at the time, but after 3 days, the sound came back again. Now, I'm driving around with the this sound happening now and then, kinda annoying. My friend suggests me to tighten it again, but some one else suggests that it's too tight... so I'm confused.

Any one had a similar sort of problem before? Any suggestions?

Any one know what sort of torque we are supposed to put onto these nuts?

The sound is only noticeable when the car is moving slowly (when the car turns or when it goes onto a bump).
oz_viking Grand Master

oz_viking

Posted
Posted

Yep same prob with the Whiteline rear sway. No idea what torque should be, but every time I tighten it the noise becomes less frequent (never really goes away completely). Some others have suggested that the non-permanent Loctite helps.

CAP Grand Master

CAP

Posted
Posted

It's needs to be very tight - use leverage, I had the same problem when I had mine installed, we used a pipe for leverage on the wrench and it fixed the problem, came back just a tiny bit a month ago which is a good 9 months after installation ( Oddly only when creeping out of the driveway ).

So I simply asked Toyota to tighten the bolts at the last service which they did with no protest. No more noise.

That's Melbourne City Toyota by the way.

I've heard the torque setting is very high for these two bolts, you will have noticed when the old one was removed the bolts were very very hard to remove.


Pippy Mentor

Pippy

Posted
Posted

1. Take it off again, MAP81 and myself had the same problem, just lube it.

2. Toyota doesn't follow the torque settings, cos we couldn't even move the bolt on shao one, even with the rattle gun on full blast.

3. Torque setting is so you can actually take it off the next time for this particular case.

:) have fun!

when i had some noise... it was when i snapped the rear sway... :D TWICE!!

oh.. and the fronts will be noisy too, but that's just the bushes... again... clean and lube.

CHA54 Grand Master

CHA54

Posted
Posted (edited)

we actually modified MAP81's whiteline rear POS on the weekend, didn't just lube it up... it's now totally silent.

I'm actually becoming dissapointed with the declining quality of the whiteline gear. I could weld better with my ****ty arc welder.

Edited by rollamods
Rolla Boy Grand Master

Rolla Boy

Posted
Posted

Are they still standard bushes??? Cause I usually remove the bushes, clean them up and lube with rubber grease... Refit all the bushes and noises are gone... Grease soaks into the bushes so they won't come back...

CHA54 Grand Master

CHA54

Posted
Posted

there are NO bushes on the POS whiteline rear swaybar.

lucio_libre Grand Master

lucio_libre

Posted
Posted

Sounds like its a common problem, I must admit I just tightened the bolts as much as I could when I installed mine and had no issues so far. Maybe whiteline need to be adressed about this.

Rolla Boy Grand Master

Rolla Boy

Posted
Posted
there are NO bushes on the POS whiteline rear swaybar.

So what goes inbetween the bar itself and the brackets??? Or are the ends only joined at the struts???

KT_haha Mentor

KT_haha

Posted
  • Author
Posted

There are just two sets of nuts and bolts on either side of the sway bar holding it in.

I'm thinking the noise can come from two places, one is from the bar touching the U shape bracket when the body twists; and the other is where the bolts are screwed in, the rubbing of the metal contact (between the bolt and the bar and the bracket) as the body twisits.

there are NO bushes on the POS whiteline rear swaybar.

So what goes inbetween the bar itself and the brackets??? Or are the ends only joined at the struts???

02rolla Rising Star

02rolla

Posted
Posted

Yeah i had the same problem with my TRD sway bar the first time i drove it after fitting.

Just tightened the absolute crap out of them and it went away.

CHA54 Grand Master

CHA54

Posted
Posted

Ben,

Haven't you ever had a look under the rear of a new corolla at work when it's on the hoist?

post-148-1126049772_thumb.jpg

kcorro Grand Master

kcorro

Posted
Posted

i have trd and it has never made a sound. izzfe has it too and he initially had sound issue but once tightened it never made a sound again.

the torque is very high for those 2 bolts. take for example the front strut bolts are 29 and the rear sway is close to 200.

could the orientation of the bolts make any difference? with stock the bolt head is at the bottom and the nut at top.

SILVABULLIT Grand Master

SILVABULLIT

Posted
Posted
i have trd and it has never made a sound. izzfe has it too and he initially had sound issue but once tightened it never made a sound again.

the torque is very high for those 2 bolts. take for example the front strut bolts are 29 and the rear sway is close to 200.

could the orientation of the bolts make any difference? with stock the bolt head is at the bottom and the nut at top.

Of all the strut braces northy and myself have fitted only 1 car was a drama getting the strut mount nuts undone. Some have been that loose that I almost got them undone with my fingers!(hey sportiv!!)

KT_haha Mentor

KT_haha

Posted
  • Author
Posted

:D

Tightened the bolts again tonight, I could only turn a little bit extra with the wrench (about 30 degrees on both sides), and now the sound is gone. Thanks guys

:lol:

CAP Grand Master

CAP

Posted
Posted

Definetely no rubber bushes where the stabiliser is bolted into the torsion beam, it's metal on metal because the stabiliser is what keeps the torsion beam assembly rigid, if there's movement between the stabiliser and torsion beam it defeats the purpose of having the stabiliser there.

  • 3 weeks later...
CAP Grand Master

CAP

Posted
Posted
Take it off again, MAP81 and myself had the same problem, just lube it.

Question: What do you mean you lubed it? Where did you apply the grease? Was it on the inside of the ends where the bolts go through or the contact points on either ends where the bar makes contact with the torsion beam ?

MAP81 Mentor

MAP81

Posted
Posted

Question:  What do you mean you lubed it?  Where did you apply the grease?  Was it on the inside of the ends where the bolts go through or the contact points on either ends where the bar makes contact with the torsion beam ?

the contact points on either ends where the bar makes contact with the torsion beam :)

CAP Grand Master

CAP

Posted
Posted

Thanx :) , mine just came back yesterday more annoying than ever, instead of the usual occassional "konk" it now squeeks like a rusty door hinge.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing



  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 8

      Android auto

      Your solution is akin to suggesting that switching to a different car manufacturer would resolve the issue. However, not everyone shares the same enthusiasm for using an iPhone as you do.
      Equi28 in RAV4 Club
    2. 1

      Turboed Corolla Overbuilt?

      that engine will be fine, the rods are the main thing to be concerned about. The 2860 is a decent turbo for the 1zz but in this day and age I'd go for a G25-550. The injectors might be on the small side, we run DW1000's. You need a full length injector, the shorter injectors with adaptors like ID1050x dont fit the 1zz head. You don't need an aftermarket intake manifold, if you do go down that path, avoid the CNC innovations unit, it's garbage. Do the boost control with a MAC valve and control it with the aftermarket ECU of your choice, I use Link stuff on most of my builds with the G4x Storm as the minimum. I also wire a fuel pressure sensor and oil pressure sensor to the ECU in my installs. Use a decent intercooler, the better cores (ARE, PWR, Garrett, Vibrant, Plazmaman, Hypertune) work a lot better than the chinese stuff like Aeroflow. a 450x250-300 fits fairly well with custom end tanks to route the cooler pipes through next to the radiator Don't forget about the clutch and gearbox. These days I like the Uniclutch twinplate, Above 300whp you'll want to think about upgrading the 3rd and 4th gears in the box also with the SSC (Hollinger) gear set and install an LSD of your choice. If you're going to give it a hard time, you'll also want an oil cooler. I like the HKS thermostat type sandwich plates and setrab or mocal oil coolers with -10 speedflow fittings/lines (Chinese AN fittings neck down to a lot smaller internal diameter in their bends, not great for flow) You'll also want to think about brakes, Celica or Sportivo front calipers will bolt on with sportivo discs as a starting point. To have somewhere like Tunehouse do the work you'll want to budget somewhere between 20-40K
      CHA54 in Corolla / Corolla Sportivo Club
    3. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      I did the mathematics myself regarding costs vs benefits for fuel injector cleaner. I have changed from 91ULP to 95PULP and 98PULP. Price difference can be about 13 -20 cents. Compared to 91ULP, Premium quality fuel should have a better quality additive package designed to have superior engine cleaning capabilities so the engine can perform at their best.
      campbeam in Camry Club
    4. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      "Fuel injector cleaner is a waste of money" Only if you by the cheap crap if you use LiquMolly a German Product it does work and you won't waste your Money.
      Aussie Camry in Camry Club
    5. 0

      Camry Touring 2010 A/C Issues.

      Hi Guys, My Camry 2010 Touring just had a regas done on it and the next day for some reason it wasn't blowing cold air but the next day it is now working with nice cold air BUT every now and then we can hear and feel a like a buzz for a few secounds and today while my sister took my I could her like a mild knock sound when stopped but goes away when driving. Any idea what this could be and the A/C is always working now for now.
      Aussie Camry in Camry Club
    6. 6

      My Toys & Collectables

      Friday the 13th added
      L4WL3SS in Club Lounge
    7. 18

      High idling on the 2zzge even when warm (solved!)

      i am in sydney, just got 1992 tarago, same problem, 2k idle speed when engine warm, changed the whole throttle body, ECU, still same, help pls in sydney 0405987988
      moxabest in Corolla / Corolla Sportivo Club
    8. 5

      High RPM Idle after the engine warm up.

      i have same problem, already changed throttle body, ecm modle, help pls
      moxabest in Inside and Out
    9. 0

      Tow bar

      Hi guys, Just bought my new Landcruiser Prado yesterday. What is the difference between Onroad Towner and Off road Towbar
      Kiru in Prado Club
    10. 3

      Disconnecting winch, lightbar and UHF

      Generally, yes. In the 60s, and earlier, there were cars with positive grounds, so I'm always a bit hesitant to say the negative wire. It is always the one that bolts to the body. Herb
      ozieagle in Landcruiser Club
×
×
  • Create New...

Forums

News

Membership