Jump to content

CHROME "KLUGER" REAR NAMEPLATE WANTED

Townsville KXS

By Townsville KXS
in Kluger

 Share

Recommended Posts

Townsville KXS Contributor

Townsville KXS

Posted
Posted

Hi guys

Im after a chrome rear nameplate my my 2008 kluger, the one that sits above the handle for the rear tailgate, i have looked everywhere. Anyone have any ideas or have one for sale?

Thanks Ray

Link to comment
Share on other sites
ianskluger Collaborator

ianskluger

Posted
Posted

I would talk to your local panel beater and get them to source it, because they would have the supplier contacts. From what I can tell the chrome name plate came out the latest model MY11 onwards.The rear door looks the same as the prior model, so I'd expect it would fit, but I would think a panel beater could tell you

Link to comment
Share on other sites

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing



  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 0

      KUN26 SR5 help mounting sport bar and 3 piece lid

      g'day, New here. Im looking for advice for KUN26 SR5. Replacing a canopy with a factory 3 piece hard and lid sports bar. Couple of issues im having is: It appears originally the tub liner would be trimmed? and a black bar (approx 50x50) is mounted to the front of the tub, where the hinges for the lid are riveted too. Rather than trim the liner, ive used an aluminium fencing rail which attached to the tub the overlal dimensions are the same and i have the lid sitting in place. All good there. However, i now have 2 issues. The sports bar mounting point at the front of the tub, is 2x20mm holes wihtout a thread. The mounting holes a little further back have an m8 thread. I reckon theres a plate with nutserts or something im missing between the sports bar and tub. What can i do here? The second, is the hard lid corner pieces dont cover the front edge of the tub and appear to need trimming. Is this normal?
      BIG BROWN SHARK in Hilux Club
    2. 0

      2004 Hilux SR5

      Just curious if anyone else is having issues with the car alarm going off randomly after mins to hours when locking with the key fob? Could this be an issue with the immobiliser?
      joshyab0i in Hilux Club
    3. 2

      1-Piece Brake Rotor?

      Hi again, Joel. Apart from being told that you should replace the rotors, what is wrong with them? do you have brake shudder, or are the rotors too thin, i.e. beyond their wear limit? If there are no symptoms of rotor problems I would clean the old ones and reuse them. Maybe new brake pads. As the hubs have come off you have disturbed the bearings, so clean them thoroughly, pack them with a bearing grease and reinstall them. Herb
      • 1
      • Like
      ozieagle in Suspension & Brakes
    4. 0

      Standard suspension

      Prob a dumb question but can you raise the height of standard GXL 2023 suspension just temp and only slightly to stop front tyre rub on inside of arb summit guard until I can get a proper lift in a few weeks thanks Jamie
      Jamie W in Prado
    5. 2

      1-Piece Brake Rotor?

      Hi Joel, From the repair manual 1989 to 2004, here is an extract about the front rotors. Herb
      ozieagle in Suspension & Brakes
    6. 2

      1-Piece Brake Rotor?

      Hi, I purchased a lovely Hiace Commuter recently and was advised to replace the Rotors. So I Bought some rotors from supercheap, and removed the old ones from the vehicle. I'm a little startled though, as the old ones seem to be one-piece. Am I dealing with a rotor that has a built-in rotor hat or hub assembly? I've attached 2x images, the old with the yellow highliting that it seems to be one piece and the new on the plastic. There is no seam on the old. I've looked at the workshop manual, and tons of videos but the one-piece doesn't seem to be standard. Model: TOYOTA HIACE RZH125R 2.4L 2RZ-E SOHC 8v MPFI 4cyl Bus 5sp Man RWD [01/98 - 12/04]
      Joel4965 in Suspension & Brakes
    7. 2

      Toyota 2023 single cab tray alterations

      Had a look at Toyota when I was there yesterday, they are screwed on
      CONROD in Hilux Club
    8. 1

      Toyota prado 2018 Rattling noise?

      Yep, we have a 2018 model and it makes the same noise. We had a 2013 model prior to that and it too made the same noise. Has anyone figured out the problem yet?
      DazzaG in Prado
    9. 13

      What do you use

      Hope the road trip ahead is wonderful my friend, enjoy the open road and scenery around you in your travels. I am glad your trying the Armor all Ultra Ceramic Glass product I love it so easy to use and the end results are great and will reaaply mine this weekend after "Faye" gets her wash and dry. I am trying out the TW Graphene Tyre shine right now and am keen to apply it this weekend as all the videos I have seen look great. Let us know how you find the Ceramic Spray for durability, I am still using the TW Graphene Flex Wax and am super happy with it. Keep Safe On the Black Stuff Mate Hugggss to you and yours KAA
      KAA in General Toyota & Other Car Discussions
    10. 0

      Workshop manual

      I have recently purchased a 2023 Fortuner and I’m looking for a workshop manual. I have looked in the usual places on the net but can only find much earlier model manuals or the very expensive Toyota subscription. I will be spending a lot of time in the back blocks so need a manual just in case. Can anyone suggest a solution.
      Steego in Fortuner Club
×
×
  • Create New...

Forums

News

Membership