Jump to content

Specifications of thermostat for 4AFE


Recommended Posts

I need to replace the thermostat in a 4AFE and am wondering what the correct specifications/dimensions for these are.  My local Toyota dealer does not have any in stock at the moment.  Checking aftermarket options to suit the 4AFE, I see different physical specifications between different manufacturers.  Some have 29mm foot size, whilst others have 27.7mm foot size.  Variations in foot-to-flange height also exist in these aftermarkets ones, some 35mm, others 34mm.

Does anyone have knowledge on what the correct dimensions are for the thermostat as if I am forced to go with an aftermarket one, I want to make sure that I am getting one that is the right specification?

Link to post
Share on other sites

Don't let all those numbers confuse you. All you need to look for is the manufacturer recommendation. If it's designed to fit the 4AFE engine, then it will fit regardless.

Here's a few to get you going. Both high quality aftermarket.

Dayco Brand

Gates

 

Edited by Tony Prodigy
Link to post
Share on other sites

There could be variations between a Gen1 4AFE (AE92) and the Gen2 (AE101) which might account for different dimensions/part numbers in catalogues.

Link to post
Share on other sites
10 minutes ago, Hiro said:

There could be variations between a Gen1 4AFE (AE92) and the Gen2 (AE101) which might account for different dimensions/part numbers in catalogues.

Yeah, more than likely the two might have different temperature ratings which would dictate the stem depth/height but the overall neck sizes should be the same.

Link to post
Share on other sites
Yeah, more than likely the two might have different temperature ratings which would dictate the stem depth/height but the overall neck sizes should be the same.

There are significant differences in head design between the two generations, so wouldn't be out of the ordinary for it to be a physically different size

 

Sent from my SM-G970F using Tapatalk

 

 

 

Link to post
Share on other sites
2 minutes ago, Hiro said:

There are significant differences in head design between the two generations, so wouldn't be out of the ordinary for it to be a physically different size

 

Sent from my SM-G970F using Tapatalk

 

 

 

Probably best if the O.P enquires with his specific build date to ensure correct fitment. You wouldn't think something as simple as a thermostat could differ from one gen of the same engine to another. Would be nice to see pictures to be able to compare.

Link to post
Share on other sites
  • 2 weeks later...

The car in question is a 1994 build.

Am also wondering if it is possible to replace the 2 studs that locates the thermostat housing and the retaining nuts screw on to.  Have seen some diagrams that indicate these are separate parts to the water inlet housing.  Or does that require special tools and it is easier to just replace the entire water inlet housing?

Link to post
Share on other sites
8 hours ago, Noodles2302 said:

Am also wondering if it is possible to replace the 2 studs

The studs are removable. Just use a pair of vice grips and gently unscrew them. Anticlockwise rotation. There may be thread lock on the threads, but they should rotate.

Vice Grips.webp

Link to post
Share on other sites

Other way to remove studs is to thread two nuts on there and then try and unscrew the inner nut, gets more purchase than a pair of vice grips and less likely to strip the thread (although you need to have enough thread sticking out for it to work)

Link to post
Share on other sites

Usually the threaded section at the bottom of the stud is not used which is why I suggested the vice grips. I wouldn't attack the working part of the thread. It's common sense right ? The two nuts will work a charm too, of course.

Link to post
Share on other sites

Replacements are proving hard to find.  Nothing in stock in the whole land for genuine ones.

Wondering if they are just mild steel studs and a generic of the right diameter, length and thread pitch would suffice?  Will do some measuring tomorrow.

Last resort will be to find a wreck and strip them out.  Not my first choice, But at least I am well practiced at removing them.  If I have to go  down this route, it won't be with vice grips.  It will be with a proper stud extractor or the two nut technique.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Toyota Owners Club AU © 2020 | This Website has no association with Toyota (AU) or Toyota Motor Corporation. | Cookies | Privacy Policy | Terms & Conditions

×
×
  • Create New...

Forums


News


Membership