Jump to content


pas-q

Regular Member
  • Posts

    12
  • Joined

  • Last visited

Profile Information

  • Toyota Model
    1995

Legacy Data

  • Location
    sydney

pas-q's Achievements

Contributor

Contributor (5/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. hi again guys.. ok prob a silly question but after installing my deck i realised it blew a fuse.. so i unhooked it (batt, ACC and ground), though i did leave the speaker connections in and would like to get an idea of what it is i did wrong so on my next attempt not to repeat the previous mistake... any ideas..p.s everything after soldered is taped up seperatly with insulator taping...
  2. i think its a stock alarm and was installed by the manufactorer problem is i never got the key for it (bought it used)..so i guess im going to have to dc the alarm by cuttin the wiring..its a big problem cos now wheneva i want to do something regarding removing the -ve terminal of the battery this alarm needs 2 be diarmed via the wiring.. guess it needs replacing..
  3. do u know where i could download 1 of the net.. i never got a user manual or a key for the alarm in the motor..to disable or enable it..
  4. ive tried to continually start it .. all i hear is "click"..then silence then i turn it off and then on again and i hear "click" ... and then i try 2 giv it a jolt of power using the jump leads.. no luck =(
  5. cnt be.. everything wrks perfectly the red go on.. the fuses all look good..
  6. yeah but that doesnt effect the cars starting and if it does it will crank ok and wont start or just wont do anything at all but if the car clicks but wont turn over that normally has something to do with a lack of power getting to the starter motor if you have a multimeter on hand you could check the voltage at the batt 12.4v is good then if you have some1 that can turn the key in the ignition see if the voltage drops below 9v at the batt if it does first remover wires from batt clean batt terminals and wires reconnect (correctly) and tighten (if theres movement in wires at battery not good conection) if still no good check all grounds for corrosion and security if still no good check conections at starter if still no good call an auto elec as it starts getting technical from there thanks yeh... im gna have to i have tightened the batt and i did clean the acid residue off it.. i think sumhow the alarm is stoppin the motor from reaching power the cars reds turn on and th headlights and blinkers.. its jst went i start it it makes a single click noise ..watta pain.. auto electricians are heaps expensive.. ive installed 2 prev decks in this car and theyve wrked fine.. only diff is ive removed the -ve terminal of the batt wen wrkin wit the electrical wiring to ensure no malfunction..and ive used the metal body of the car as a connecter for the ground wiring of the deck as it says to do so in the instructions of the deck..
  7. hey gys.. jst wanted some ideas? i installed and soldered my after market deck into my car.. as i went to switch on the car.. it wuldnt start and made a clicking noise then the alarm of the car sounded hwever it went off in a sort of low tone sound.. i dc the ACC, batt and ground wires of the deck hwever no change.. i used jump leads to start the car thinkin it may of drained the batt and again no luck.. the batt i tested and it had full battery.. i think its 2 do wit the alarm sumhow not allowin power to the motor not quite sure.. hwever any idea on what the prob is and hw to fix it? btw this is the 3rd deck ive installed in this car.. only diff is this time i took out the -ve terminal of the engine battery and instead of connecting the ground wire of the deck to the ground wire of the car ..i connected it to the metal body of the car via a screw..
  8. hey gys.. jst wanted some ideas? i installed and soldered my after market deck into my car.. as i went to switch on the car.. it wuldnt start and made a clicking noise then the alarm of the car sounded hwever it went off in a sort of low tone sound.. i dc the ACC, batt and ground wires of the deck hwever no change.. i used jump leads to start the car thinkin it may of drained the batt and again no luck.. the batt i tested and it had full battery.. i think its 2 do wit the alarm sumhow not allowin power to the motor not quite sure.. hwever any idea on what the prob is and hw to fix it? btw this is the 3rd deck ive installed in this car.. only diff is this time i took out the -ve terminal of the engine battery and instead of connecting the ground wire of the deck to the ground wire of the car ..i connected it to the metal body of the car via a screw..
  9. um if i buy the uuniversal muffler can i install it all by myself or better off professionally?
  10. do you think if i attach a muffler tip with a very large diameter it will increase the noise
  11. hey guys, new here.. just wondering i have a gen1 paseo i wanted to make the exhaust noiser so i added a muffler tip to the exhaust end and that didnt work sounds almost like stock.. i dnt wana spend too much on it ..any ideas what i can do witout having to take it like the exhuast shop cos i know its costly there and i prefer to do it myself. thanks
×
×
  • Create New...

Forums


News


Membership