Wokstar86

Hey all, i got a zre182r. Looking to upgrade - Brake pads, rotors and fluids. Any suggestions on brands?

Thanks.

Hey all, I got me a Zre182r. Looked and found coilovers, bc racing z1 series part number c-116-vm.

Looking for a place to get them installed, that way if it ******s out its there fault and not mine.

Anyone know of any places that does a good cheap at a fair price?

Option1 garage are doing a special where you buy coils from them $1199 and get install and allignment for $350

Anyone know anyone who can beat that?

Let me know, thanks heaps peeps

peace

Id go 3" of turbo cars are running 3" I don't see why a super charger can't

There is a trd exhaust for the zre152 but requires the tiniest amount of modification. But a rear bar/diffuser is needed to fit it because it is central tip. I hope this info helps.

Must be below 83db. Custom headers have to be made. I myself have a zre182 and have done research. Custom headers and full pipes with high flow cat and cai or Sri won't give enough gain for you to feel any power difference. Unless you turbo or cams and tune. I got quoted, 2 1/4 mild steel high flow cat and custom headers for 1500.

There's a certain quality with speakers. So if it's all toyota leave as is. Or change the lot, that way everything is upgrade and level.

From what I can see dude. Hb3 kit or 9005 kit. You may have to cut the rubber seal to fit it. Hope that helps.

Parts in sourcing use factory mounting points so I'm covered. I may get a little tricky and get a ram pipe leading to it too.

Taking out the power figures. Would you say the an aftermarket cold air or short ram would increase throttle response also?

I'm not looking for "big" numbers in power gains as nice as that would be. We all know that they give small gains but it all adds up in the end.

Hey errybody, I'm currently wanting an intake system for my 2013 zre182 manual. I took a look around and it looks like there is minimal out there. The only one I found is a K&N one for 700+usd not including shipping.

I was wondering if anyone know of any other or other options for a SRI or CAI for this car.

Helpful input is muchly appreciated.

Thanks peeps.

Hey. The rims are 16x7 with +30 and I dipped the car myself.

Spring exhaust and intake are hard to source. No one's made anything yet. I'm in the same situation.

Sunraysia 16x7 with falken 225/50/16

Do you have a picture of your wheel with this tyre on it? Im interested to see how it sits.

I would think that it would be bulging out? I recently got some 16x7 wheels which need new tyres

Thanks

Its not that bad. Pics will come shortly. It's a fat rim, it sits a few millimetres out but is slowly self cambering in. You can get a 215 to sit on your wheels, it will give it a bit of a stretch.

You might want to think carefully about any modifications that increase vehicle noise. A 2013 Corolla needs to comply with ADR83/00, which is extremely strict as regards noise - specifically exhaust noise when measured using a specific stationary test and also overall vehicle noise when performing a specific drive-by test (mind you, in Australia we only appear to use the stationary noise test for in-service vehicles).

Your 2013 Corolla hatch cannot measure any more than 83 dB in the stationary exhaust noise test. The stock car is already 78 dB and my TRD axleback exhaust is already just under the legal limit (82.7 dB which rounds down to 82 dB under the legislation). The TRD exhaust is one of the quietest exhausts around -even quieter than a stock Toyota Yaris exhaust. Most aftermarket exhausts will push the Corolla into illegal territory since the lenience allowed from stock is so small these days (as mentioned, there is only a 5 dB allowance given for your 2013 Corolla).

As for Varex exhausts, you would need to check for legality issues in Queensland. Here in NSW, they are illegal since they are considered to be a temporary noise reduction device which is outlawed under clause 18 of our Protection of the Environment Act (Noise Control) 2008. If you were caught with a Varex by the police here in NSW, you would get a $200 fine for having the actual exhaust installed. If the police happened to have EPA personnel with them (and they sometimes do), there would be an additional $400 fine for the noise it makes.

To be honest I just don't think it would be worthwhile, since you would only need to be pulled over by the police or have someone report your exhaust noise and you would be in trouble. The breathing mods could also be suspect as they obviously increase the overall noise signature of the vehicle.

Personally I couldn't really car less about aftermarket induction and exhaust mods (within reason and when used at acceptable times of day / night) but rules are rules and you need to understand what you are getting into.

how much was trd exhaust?

Hi guys. I have a 2013 corolla ascent sport and looking to mod it.

Atm I have

White led Parker and license plate lights.

Removed the ascent sport badge.

Near finished plasti dipping the external chrome trimming black.

Sunraysia 16x7 with falken 225/50/16

Also have a kicker sub and amp wired to stock touch screen media player

player.

HID Kit coming soon.

Looking for simple performance mods.

Id love some advice on what breathing parts to get. Obviously headers, high flow cat and cai. But need suggestions on brand and pricing.

ALSO id love some coilovers but once again, need help on brand and pricing.

Hoping to get muffler to keep noise down or varex muffler so I have options.

Not looking to track this thing, it's my daily. Just wanna give it a few defining characteristics and a lil extra kick.

Much appreciated guys

Hb3 hb4 dude. I'm having the same issue. I'm essentially buying cheap hb3 hb4 bulbs to see how aftermarket fit. Then sourcing a decent hid kit from the on. I'll keep you posted

specs on exhaust?

problem solved peoples, went to autobarn and had one of the fellas take a look and showed me.

thanks anyways

Hey all, I own a Toyota Corolla Ascent Sport ZRE182R (2012 - 2013) and I'm wanting to change the parkers for it. Ive read the manual but diagrams dont match what I see in the engine bay.

I also want to get new Headlights for it too but im not sure on size or model bulb to get for it.

Any tips or tricks on how to replace these parkers would be awesome.

If anyone can help with this it would be muchly appreciated.