RODNZ

similar incident

http://forums.toyspeed.org.nz/viewtopic.php?t=88693

did you resolve this? could be a fuel filter problem...

In NZ, i saw these for sale; http://www.trademe.co.nz/motors/car-parts-accessories/performance/electronics/auction-400382509.htm

maybe its the same part number?

Oh yes I saw that, but doesn't show you where you take off the star screws and oil the bearings inside, should rotate freely inside. Just had to mark it so it lines up properly afterwards when you put it back together.

I came across this thread on how to fully take it apart and clean it...

http://matrixowners.com/?showtopic=65513

There is going to be a new kid on the block with a TRD supercharger kit in NSW soon to be! hahahha! i WOnder who!?

Jesus?

You need a HB4 kit. The HID kit type you need is the same as your Halogen bulb, this is for fitment in your headlight. The HID (ZR) headlight will require D4R globes, which fit the HID headlight sockets...

Dutchie101,

Thanks for the clarification mate. Planning on getting the HB4 kit for my ZRE sedan to test them out. If its too much glare hopefully they will fit my Dad's 07 Camry Grande, since the Camry comes with projectors already.

Also another thing to rant about, how can a $40000 Camry not have HID standard!?!

Recession

your manifold has warped perhaps, stud will be broken off probabily at the end closest to your altenator

check out this video

after reading this thread I was curious and investigated my runx to see if it had one...

and

Yay my Runx came with a filter and it had some leaves with it

From Japan, I guess theyre not made the same way

I think the connectors are different, my Runx didnt fit aftermarket ones which were made for NZ corollas

I would have thought windows came tinted from factory (except front sides) like my corolla.... guess not

Looks ghey

TBH I quite like that gearknob, nice to hold

Well when I got my rear lip put on I had a choice of cutting the lip or get the exhaust tip rewelded, I went with the rewelded option. I got them to lower it and extend it so it now sits lower and extended a bit so the fumes dont mark the rear bumper

I have a TRD High Response Muffler

Ive seen rear lips here in NZ put over the back, looks as though the factory exhaust tip is pointed down and no modification is needed

you can get a trd cai from here not too sure if they send to nz but worth a shot.

http://www.chtoyota.com.au/parts.asp

550BUX? wow thats alot for a piece of aluminium and pod

not sure if it fits this corolla but says Twin Charger? what ever that means http://broomfish.co.nz/product_info.php?cP...products_id=606

or cold air intake by simota, again not sure if it fits http://broomfish.co.nz/product_info.php?cP...products_id=735

Well

My corolla didnt have a rear skirt when it came from Japan, Im guessing because it had a big bore and could not be fitted so they went without, but then when it came into NZ for compliance it had to be removed due to it having holes in it. They replaced it with a TRD High Flow one which is probably better since i dont like exhaust noise from N/A cars.

I then went out and got a rear skirt from Toyota Hamilton and that was not cheap. also I got the exhaust tip rewelded as i didnt want to cut a hole in the rear skirt.

I prefer it on as it looked funny with a body kit and it being low you could see the exhaust.

just wanted to throw this question out there, is it posible to remove the pcv system and replace it with a traditionl setup? or is there no point to this, im guessing the pcv system is better cause it uses a vacuem system... but would it hurt to change it to traditional setup?

Whats the traditional setup?

dont meant to be ignorant but what are these slimlines you talking about? <_<

lol the weather guard things along the windows, that block out the rain and wind

oh lol

Really you cant get them? some people hate those things, I like it when i park my car somewhere I can wind my windows down a little bit on a hot day, if it decides to rain no problem!

Im not sure if these are on the New Zealand model Corollas...

nicee ride man.. the front kit looks like the pulsar sss kit.. but yer any differences with the computer or anything.. like wat does ur lift kick in at and hows ur gearbox..

Dont think theres any differences in what ive been reading, think its just the same as your guys corolla probably all made in japan assembled at different country <_< , lift at 6000rpm and a 6speed gearbox and it feels fine

SEXY!!, sometimes i wished i got black or white

hmmm i asked my mate at toyota to ask the parts department and they said they cant get the slimlines :( only the regular ones for the two fronts

dont meant to be ignorant but what are these slimlines you talking about? <_<

nice and clean, those window guards are they factory import?

Yes came as a factory import. (Its clean because I just washed it)

Car came in with the body kit (except rear skirt), lowered and with the TRD Exhaust and Apexi Pod. Only thing I had to get were the rear skirt from Toyota, oh and the rear tail lights...

Thats a clean machine, very nice.. Curious though,why is your exhaust on the left? is that a 1.5 4WD Runx?

Thanks

Its the TRD High Flow Exhaust (modified tip to go under the skirt) and its the FWD 1.8 2zzge engine. Its a Runx Z

Hello Everyone

Im from New Zealand and I see that Australia has something similar

Its a 2002 Corolla Runx imported from Japan

Here is my new car I'd like to share...