Jump to content


question re repairing door sill trims '90 Camry

pax-eterna

By pax-eterna
in Camry Club

 Share

Recommended Posts

pax-eterna Progessing

pax-eterna

Posted
Posted

Just wondered if anyone had come across a trick (or workaround) to repair the plastic door sill trims screw mounts?

The ones on my vehicle the screws simply keep spinning around without tightening and when the trim is removed you can see why. Each trim has a plastic "wedge" under each hoe that snaps into a rectangular hole in the door sill panel and then the screw goes into this. But in this case the screw can no longer get purchase.

Is there any solution anyone can think of without the need for me to go to Toyota for parts replacement?

Any opinions welcome as something someone says may trigger and idea to me for a way to repair it.

Thanks

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing



  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 3

      What can cause 2x bolts Missing on break calipers?

      In my humble experience with our car and Toyota - the majority we came across travelling around Australia towing a van is they are uncaring, irresponsible and possibly dangerous. One of them forgot to tighten the front wheel. Imagine the disaster if the wheel had decided to part company at 90kph towing a 3t caravan.
      larry200 in Corolla / Corolla Sportivo Club
    2. 0

      02 mcv20r no go

      have a 02 camry with 1mzfe engine...runs lpg as well as petrol. lpg mixer suffered a intake preiigition and had to be rebuilt. however will now willnot run on petrol. fiers but immediately stops. have replaced eveyrthing from fuel pump forwards, mas,ignition module, ecu, etc. no fault codes on obd2. had a local mobile mechanic have a look with no joy....any thoughts out there?
      fwb in Camry Club
    3. 1

      Towing with landcruiser 300 series

      Good practice to tow in 4th. Lots of information on the now defunct LCCOL forum but everyone was in agreement about towing in 4th. I have done this towing a 3.5t rated van. Fuel consumption is so similar it is not an issue. It is more about getting the engine spinning. New diesel like to spin as opposed to chug along like the old style ones. Proof for me was when I had the ECU remapped and installed a lockup kit. Whilst the car was happy to hold 5th and 6th - extra power and locked - the EGTs were telling a different story. Towing in 4ht at a GPS 90 - 95 kph turned out to be the best combination for forward progress and fuel consumption.
      larry200 in Landcruiser Club
    4. 3

      Remote batteries going flat very quickly

      There was a post on the now defunct LCOOL forum whereby you could put your remote in a 'sleep' state and save the battery. It seems the remote is constantly looking for a signal which in turn drains the battery.
      larry200 in Landcruiser Club
    5. 0

      Major Oil Leak

      tragedy has struck 😔... my 07 SX6 suffered a major oil leak this morning. Got a low oil pressure alert, pulled over. dip stick was bone dry with small amounts of metal flakes on the end. i'm assuming the leak is caused by either the oil cooler lines or the vvti rubber line deterioration. Car has been towed to my house. Whats the best course of action now? fix the leak and do a few oil flushes? or do i need a whole new motor?
      wessen in Aurion / TRD Aurion Club
    6. 0

      TRD Front Strut Brace to suit ZZE122/ZZE123

      1 x Used original grey TRD Front Strut Brace to suit ZZE122/ZZE123 (Discontinued years ago – rare): In excellent condition for age, minor cosmetic issues near bolts. Advertised elsewhere as well. AUD$420 Cash pick up only NO OFFERS PLEASE– located in Elanora Qld 4221. I have repair kits for the centre console door available also
      chrislb in Buy & Sell - Parts and Accessories
    7. 0

      H7 12V 55W Replacement - No Retaining Clip

      Hi all, I lost the hi beams retaining clip for the hi beams bulbs on my Toyota, is there a replacement that I could get that doesn’t need that retaining clip? will take any help. The stock bulb for my vehicle is below.
      Ashanifs in Corolla / Corolla Sportivo Club
    8. 0

      ST-162 front door-glass seal availability

      Hi all, my wife has a 1988 ST-162 Celica which I have been lovingly caring for since we met 25 years ago. It is in VGC, but of late the wind noise at freeway speeds has become much louder, and with the current wet weather the front doors are leaking rain through the 'seal' point between the window glass and the door seals. The doors are hanging in the proper position and the windows do not seem to be unduly loose in their carriers. I am trying to find a new set of door seals to try to fix the problem, but have had no success anywhere. Any ideas or suggestions would be most appreciated! My mobile is 0427 478874, or reply here!
      Tim Bailey in Celica Club
    9. 3

      What can cause 2x bolts Missing on break calipers?

      It was done right 5 months ago.. ok… Now I am even more scared.. cuz it was done by Toyota Service Centre.. they replaced both brake pads.. 😖😖
      EmmNa in Corolla / Corolla Sportivo Club
    10. 0

      Took the dust cover off, heart skipped a beat

      Not sure how many of the old guard are still around… fluids drained, fuel tank cleaned and lines purged, might be time to throw it into gear again.
      • 1
      • Like
      Zoran in Members Rides
×
×
  • Create New...

Forums

News

Membership