Jump to content

2010 'rolla cartrige oil filter....special service tool..??

ganyb

By ganyb
in Corolla / Corolla Sportivo Club

 Share

Recommended Posts

ganyb Community Regular

ganyb

Posted
Posted

Hi all..just got the new oil filter cartridge , all set to go, when reading the fitting instructions, it says I must use s "special service tool".

Has anyone DIY changed their filter yet, and is it possible to do this without having to buy this tool...??? and if so what did you use to remove/replace the filter canister...?

Thanks fellas...

Link to comment
Share on other sites

ganyb Community Regular

ganyb

Posted
  • Author
Posted

...K checked on ebay, seem to be some on there about $25 ...next question .. can anyone confirm if 64mm 14 flute to be the correct size for the new canisters...if not what would the correct size be..??

thanx for any help.

Link to comment
Share on other sites
ganyb Community Regular

ganyb

Posted
  • Author
Posted

..well just bought one on the 'bay from a seller in NZ, 65mm is the size, and it was $23.40 incl postage.

I CANNOT BELIEVE..!! that Toyota have done this, the actual canister is made from PLASTIC ! not metal, if the perfectly fitting tool is not used, the edges of the 14 sides can easily burr over possibly making removal or replacement eventually impossible.

Also the parts dept at my local dealership, said replacement takes their workshop twice as long and that actual cleaning of the inside of the canister is very important ( I wonder how many wont bother to do this, or even wont bother to change the filter at all.?? )he also said it was a cost cutting exercise, although Toyota are spinning it as "more environmentally friendly".

..cant believe I've just completed a whole thread just talking to myself..! :lol: all good but..

Link to comment
Share on other sites
juvenile Grand Master

juvenile

Posted
Posted

I'm confused, what is an oil filter cartridge? and plastic? I've had a quick look at my oil filter before but it looks like a normal metal screw on type, have I missed something?

I have one service left till warranty ends then I'll do it myself so I better investigate I think..

I have a genuine filter removal tool for my 4AGE filters which I thought may fit the ZRE and it was a perfect fit for the Valvoline replacement too (Z386)

I'll check if it fits the ZRE

Link to comment
Share on other sites

ganyb Community Regular

ganyb

Posted
  • Author
Posted (edited)

I'm confused, what is an oil filter cartridge? and plastic? I've had a quick look at my oil filter before but it looks like a normal metal screw on type, have I missed something?

I have one service left till warranty ends then I'll do it myself so I better investigate I think..

I have a genuine filter removal tool for my 4AGE filters which I thought may fit the ZRE and it was a perfect fit for the Valvoline replacement too (Z386)

I'll check if it fits the ZRE

..mid 2010 ZRE's, Toyota went from the no-brainer spin-off/spin on steel filter (yours) to a plastic housing (mine) containing a paper oil filter (04152-37010), you were lucky enough to have the pre plastic one..

Edited by ganyb
Link to comment
Share on other sites
juvenile Grand Master

juvenile

Posted
Posted

I'm confused, what is an oil filter cartridge? and plastic? I've had a quick look at my oil filter before but it looks like a normal metal screw on type, have I missed something?

I have one service left till warranty ends then I'll do it myself so I better investigate I think..

I have a genuine filter removal tool for my 4AGE filters which I thought may fit the ZRE and it was a perfect fit for the Valvoline replacement too (Z386)

I'll check if it fits the ZRE

..mid 2010 ZRE's, Toyota went from the no-brainer spin-off/spin on steel filter (yours) to a plastic housing (mine) containing a paper oil filter (04152-37010), you were lucky enough to have the pre plastic one..

Thankyou for clearing that up, I had no idea,when you change it could you post a pic of it,only if you can or remember.

Cheers :)

Link to comment
Share on other sites
Rolla Boy Grand Master

Rolla Boy

Posted
Posted

It's the same tool thats used on the Aurions and new Klugers...

Make sure not to overtighten the filter housing as it will become impossible to remove the next time you try... Depending on your special tool, I use a 1/2" bar to remove the housing and a 3/8" ratchet to tighten...

Link to comment
Share on other sites
ganyb Community Regular

ganyb

Posted
  • Author
Posted

It's the same tool thats used on the Aurions and new Klugers...

Make sure not to overtighten the filter housing as it will become impossible to remove the next time you try... Depending on your special tool, I use a 1/2" bar to remove the housing and a 3/8" ratchet to tighten...

Tks for that Ben...I'll be sure sure do as you advise....tks mate..

Link to comment
Share on other sites
dwee. Grand Master

dwee.

Posted
Posted

I'm confused, what is an oil filter cartridge? and plastic? I've had a quick look at my oil filter before but it looks like a normal metal screw on type, have I missed something?

I have one service left till warranty ends then I'll do it myself so I better investigate I think..

I have a genuine filter removal tool for my 4AGE filters which I thought may fit the ZRE and it was a perfect fit for the Valvoline replacement too (Z386)

I'll check if it fits the ZRE

..mid 2010 ZRE's, Toyota went from the no-brainer spin-off/spin on steel filter (yours) to a plastic housing (mine) containing a paper oil filter (04152-37010), you were lucky enough to have the pre plastic one..

Thankyou for clearing that up, I had no idea,when you change it could you post a pic of it,only if you can or remember.

Cheers :)

Hey, I believe (saying believe because I'm not too sure what you mean by plastic and all) it's 2009 onwards ZREs. I know mine has paper oil filter and is different to 07 and 08 ZREs.. :huh:

Link to comment
Share on other sites
DJKOR Grand Master

DJKOR

Posted
Posted

In terms of the design, I actually must say that I quite like it. I prefer it over the typical canister type that we are all familiar with. When used correctly, it results in less mess because you can drain the oil filter prior to removing it. As well, the o-ring seal is superior (in my opinion) to the traditional oil filter seal.

But plastic? That sounds quite dodgy. If that's the case, I wouldn't be satisfied with the design. The metal one used on the Aurion has a couple of tabs on the top which when put together with a little creativity, can be removed without the cap style oil filter wrench. I've managed to remove the one on my last Aurion several times, and my new one a few times without the proper tool and have not put a single scratch in it.

I'd be curious to see a photo of this plastic version your car has.

dsc05577x.th.jpg

Link to comment
Share on other sites
  • 2 weeks later...
juvenile Grand Master

juvenile

Posted
Posted

I have one service left till warranty ends then I'll do it myself so I better investigate I think..

I have a genuine filter removal tool for my 4AGE filters which I thought may fit the ZRE and it was a perfect fit for the Valvoline replacement too (Z386)

I'll check if it fits the ZRE

Cool, my 4AGE filters do fit my ZRE, good thing I kept them :D

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing



  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 0

      New member seeking advice for parts

      Hi guys! I'm Alberto, I just finished importing a HZJ73 from Japan and I love it! The car came without spare wheel holder and it seems discounted so I don't know what do to. Someone knows where I can find it or what else works as replacement? I don't mind if is not oem part as far as it works 😅 I'm based in Brisbane if it makes some kind of difference Pictures attached as reference
      alberto965 in Landcruiser Club
    2. 39

      Pics of my Kluger steering wheel removal

      What are you trying to say Don? _______________________________________________________________ skysmotor.co.uk sells the following products online: ac servo motor, geared stepper motor, stepper motor drivers, planetary gearbox and can be purchased online if required.
      Maria in Kluger Club
    3. 14

      1zz to 2zz

      hey daniboy this is one of those situations where i’m stuck and going through old forums haha currently doing a 2zz swap on my zze122 wagon and i’m having a fuel pump not priming issue, any chance you could respond back 10+ years later
      chrisibrahim in Corolla / Corolla Sportivo Club
    4. 0

      Can I put a 2010 bumper on my 2008 Camry ?

      I have a 2008 Camry altise and recently damaged the front bumper and i'm wondering if I can fit a 2010 sportivo bumper on to replace it. It looks like it fits I know I will need to get new headlights for it to fit but do I need to do any modifications or will all the plastic clips and screws line up ?
      Angus_reynolds11 in Toyota Guides Support Topics
    5. 5

      My Toys & Collectables

      Seinfeld added
      L4WL3SS in Club Lounge
    6. 0

      Anyone else tried these seat covers ?

      these seat covers look pretty good, but I've had bad experience when trying to fit some cheaper ones I bought online - they say custom fit, anyone else tried them ? Would love to know before I buy them, thanks all https://mycustomcar.com.au/
      MacSammy in Landcruiser Club
    7. 1

      Digital Speedometer

      Hi did you figure this one out? I have the same model and been unable to get it digital as well
      TrishB in Kluger Club
    8. 0

      am2 fuse blowing

      Hello, i have a 1996 starlet The problem is when i turn the key the fuse blows, and i have been looking over the wiring and can’t find any shorts or damaged wire. The car would not crank over because of the fise blowing. I found out that if i disconnect the transponder key ecu the fuse is holding, but as soon as i connect the transponder the fuse blows. So i wonder if there is something I can try out? should i just buy a new transponder box or is it something else i could try? and is it not kinda wierd that the box is the problem? I have looked inside the box and cant see any corrosion in the box
      danny98 in Starlet / Sera / Paseo Club
    9. 0

      Toyota Celica '96 5S-FE no spark

      Hi everyone, I have spent too much time on my Celica and even my mechanic is stumped at figuring out the issue so any tips will be appreciated. Here is what has been done, immobiliser disbabled, distributor replaced, igniter replaced, EFI relay replaced, and EFI 15AMP fuse is not blown. I tried jumping E1 and TE1 in the diagnostic port to try and get a code from the CEL but it doesn't light up, I think it might be burned out so I will have to get on that. I am now clueless about what to do next, it could be the ECU but I can't find any pointers too that.
      carsarepain in Celica Club
    10. 0

      Toyota Camry 2003 Driver seat recline issue

      Hi guys, so i just bought a 2003 camry. So something is wrong with the driver seat (manual recline). When i recline it at a certain place it locks in but if you put ur body force the seat tilts back a bit and locks to a different position. Looking help if someone knows whats wrong and how to fix it.
      Rafidmeme in Camry Club
×
×
  • Create New...

Forums

News

Membership