Jump to content


zze122 full respray flared guards plenty more


Mystik rolla

Recommended Posts

hey guys

here is my corolla from 4 yrs ago. was our first family bus.

This is night we got it.

12122009916.jpg

the very next day..

15122009927.jpg

14122009925.jpg

17x7 speedy lite 5's that came off our previous car which was a mx5.

couple days later.

17122009930.jpg

17122009934.jpg

  • Like 1
Link to comment
Share on other sites

The this was great for 2 yrs or so until we had another child. so we upgraded to a 2010 camry

i kept this for me. throughout its life it had numerous dents etc which i repaired and spot primered.

Drive like that for a while until i cracked it.

it was time to respray it.

Initially was going to be a standard respray inside and out. factory colour with flakes in the clear.

as you'll soon see this got out of hand.

this is the day i started to strip her down.

20121130_131717.jpg

20121201_134958.jpg

20121201_135007.jpg

20121203_104856.jpg

20121203_104930.jpg

Link to comment
Share on other sites

Then i decided the standard body wasnt good enough.. so i ordered flares.

fibreglass. riveted and glued. then moulded to body and bumpers. Rear guards cut and rewelded front sliced back to give maximum clearance.

20121203_171649.jpg

20121204_160126.jpg

20121206_144841.jpg

Welded up my antenna hole as well

20121206_133335.jpg

Link to comment
Share on other sites

Next cam the kit. got myself a levin lip and skirts.. i much prefer these.. i dont like the lil vents that the tivo ones have. also the levin skirts are a bit more curvy.

looks a lil cleaner to me.

here is a pic of the widened front with the lip pretty staunch.

20121206_154645.jpg

Wheels of choice. 15x8 +20

20121220_193841.jpg

20121220_193858.jpg

Link to comment
Share on other sites


Thanks Jeffy!

ok carpet..

013.jpg

old school carpet. super thick. Those sections are glued in. then there are mats that go in the middle. Overlocked and stitched to a 20mm foam layer. the carpet pile itself is very deep.

the door trims

IMAG0530.jpg

IMAG0529.jpg

then console and gear boot

IMAG0608_1.jpg

dash! this is me second favourite bit.

IMAG0611.jpg

Front seats extra 25mm overall foam and 15mm bolstering. super comfy

IMAG0612.jpg

I dont have a pic of the roof lining but thats also been redone in black Velour.

here is my rear seat currently still awaiting the bottom half.

IMAG0649.jpg

random pic

IMAG0651.jpg

  • Like 2
Link to comment
Share on other sites

Looked good out the front of my house the other day lol

The pics don't do this car any justice man. This thing is soooo PIMP!!!!

Luc you are a re very talented man. Now hurry up and paint my car haha

Nice work brother see you Friday :)

Link to comment
Share on other sites

  • 6 months later...

Sooo well. i have a few updates. two weeks after it being on the rd i smashed it. Not badly but enough to destroy a wheel. destroy my drivers headlight, bumper bar and both drivers fenders.

Hill runs + wet conditions + mudslides = guard rail.

anyway i fixed it all and got it in primer. couple months passed and knock knock.. ye old 1zzfe spun no.4 rod bearing. ergh second motor down. so i researched the engine a bit more to find its pretty common once u give it hell and turn corners.

Confirmed this once i stripped the motor down.. the oil pickup is in a dumb spot.

So.. motor is stripped bare. Forged rods and pistons on the way. garret t28 turbo, full water to air intercooler setup sitting at my shop. Will be collecting parts over the next few months and it'll be going back on the rd as a built turbo motor.

Also Shaved door handles and fender indicators. So another respray.

Project cars never end.

Link to comment
Share on other sites

Left hand corner. Down a hill. U can imagine how grippy it is. I was hooking. Powered out of the corner as soon as it came up to limiter it's started rattling real bad. Basically the hard cornering and the high revs it starved out of oil. Spun number 4 and by the looks of it number 3&2 were very close as well.

Link to comment
Share on other sites

If u crack open the sump and look at where the pickup is it obvious why u can have troubles. The baffling is poor and the pickup is no where near the deepest part of the sump. Aftermarket dumps are available. They have larger capacity and trapdoors to ensure good oiling under any condition.

Link to comment
Share on other sites

  • 2 weeks later...

Love this thing. Pity you smash it dopey ;)

But that interior looks even better in real life. Can't wait for you to start bringing it out to meets again.

Dem flares!!!

Get a profile pic!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 1

      New member seeking advice for parts

    2. 1

      New member seeking advice for parts

    3. 39

      Pics of my Kluger steering wheel removal

    4. 14

      1zz to 2zz

    5. 0

      Can I put a 2010 bumper on my 2008 Camry ?

    6. 0

      Anyone else tried these seat covers ?

    7. 1

      Digital Speedometer

    8. 0

      am2 fuse blowing

    9. 0

      Toyota Celica '96 5S-FE no spark

×
×
  • Create New...

Forums


News


Membership