Jump to content

Dyno question

Guest

By Guest
in Corolla / Corolla Sportivo Club

 Share

Recommended Posts

Guest

Guest

Posted
Posted

Hi all,

had my ascent dyno'd yesterday at tcc.net dyno day and just had a quick question about the torque curve:

graph.jpg

Is it normal for a STOCK corolla to have that many dips in the torque curve?

I mean the power figure is ok nothing to be ashamed of on 85.9kw but the torque curve just looks odd to me...?

btw. Bear in mind that the scale on torque is 2nm for each increase / decrease...

*shrug* thoughts people?


ZEEROLLA Grand Master

ZEEROLLA

Posted
Posted (edited)

85.9kw @ flywheel sounds really off to me and at 165-170km/h?? (4th/5th gear?) Should have been done in 3rd gear. Your rolla is 1ZZFE engined right? You should get close to 100kw @ fly and abt 75-80kw @ wheels. I don't know anything abt reading torque curves but i hav a rough idea abt tractive effort on the dyno dynamics printouts.

Z

Edited by ZEEROLLA
Guest

Guest

Posted
Posted

Z..

Engine is 1zzfe yep yep and not sure what gear it was done in ...

*I wasn't watching that part - I was watching the screen*

not sure if because it's a hub dyno if the speed reading is accurate..... (don't know enough about hub dyno's) I do remember looking over and seeing my speedo in the car up around the 120kph mark........

hmmm more oddities...perhaps I'll have it dyno'd again soon and see if there's any difference in the performance.

SILVABULLIT Grand Master

SILVABULLIT

Posted
Posted

Hub dyno's give totally different readings to say a dyno dynamics dyno. Figures are higher etc and is a little hard to compare what is classed as "the norm". :D


oz_viking Grand Master

oz_viking

Posted
Posted

Ben,

I'm disappointed you didn't get near the 195kw of the SSS with the SR20DET :) :)

As Silvabullit said, the hub dyno will read differently compared to a drum dyno as there is no wheel slip and different rotational mass once you've removed the front wheels. But - if you continue to use the Jaustech dyno after your planned power ups then it should provide a valid comparison.

oz_viking Grand Master

oz_viking

Posted
Posted (edited)

PS. did you get the lambda/AFR graph as well? That may indicate whether your ECU was playing with the fuel ratio at the point where the torque dips slightly.

Also, you can tell which gear the run was performed in by checking which of your gears matches the indicated 4.116 ratio (actually scrap that, as 4.116 will be the gear ratio x the final drive ratio)...

Edited by oz_viking
Northy Grand Master

Northy

Posted
Posted

it was done in 4th gear. cause 4th tops out at around 180km/hr (track tested) so doing 170km/hr @ 6200RPM would sound about right

Guest

Guest

Posted
Posted

Yeah I was a bit disapointed that I couldn't match that pulsar...

*shrug* most of the nissans that rocked up put the toyota's to shame power wise anyway : :huh:

I didn't end up getting an afr graph mostly because after you guys left they stopped bothering with the exhaust monitoring....

ECU modifiying things on the fly would sound about right - I mean it's not a HUGE dip when I look at it - it's only 12nm....*shrug*

I know what will fix it though B) nice size snail......

on the big happy side - Riding in the sportivo was a blast!!!

I know understand why you all love the 2zzge so much -=- cheers Camthumbsup8de.gif...

and everyone else for contributing about hub dyno's...still so much for my computer nerd head to learn :D

oz_viking Grand Master

oz_viking

Posted
Posted

No probs dude. Always happy to spread the lift-love.

And besides, I'm hoping for a ride in your beast when it's boosted :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing



  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 0

      Remote start

      What bipass do i need for immobilliser to install a remote start to my 2021 hiace
      chris mc1 in Audio/Video/Electronics
    2. 1

      1999 Camry Driver's door locking hatch issue

      It's possible that it could be something fouling or dirt build up, dry, or a broken mechanism, so have a look and give the mechanism some lubrication, most likely though, it'll be the actuator. I found one for a good price on Ebay, $25 delivered: Front Door Lock Actuator Right Side For Toyota Camry 1997-2001 | eBay
      Monad in Camry Club
    3. 0

      Query about the correct rotors for 2006 ACV40 Camry.

      Hi, I'm looking at a set of front rotors for an ACV40 2006, 2.4L Camry. I got a good price on some RDA's at Sparesbox. However both RDA8112 and RDA7686 show as for my car and I'm wondering what the difference is and if there were changes to the rotors during the model production. So does anyone know which rotor is the correct one? Many thanks in advance.
      Monad in Camry Club
    4. 9

      Android auto

      It's a simple solution though? Already laying down 60k for a RAV4, so what's another 1k on a phone to make everything work seamlessly? 👍
      L4WL3SS in RAV4 Club
    5. 9

      Android auto

      Your solution is akin to suggesting that switching to a different car manufacturer would resolve the issue. However, not everyone shares the same enthusiasm for using an iPhone as you do.
      Equi28 in RAV4 Club
    6. 1

      Turboed Corolla Overbuilt?

      that engine will be fine, the rods are the main thing to be concerned about. The 2860 is a decent turbo for the 1zz but in this day and age I'd go for a G25-550. The injectors might be on the small side, we run DW1000's. You need a full length injector, the shorter injectors with adaptors like ID1050x dont fit the 1zz head. You don't need an aftermarket intake manifold, if you do go down that path, avoid the CNC innovations unit, it's garbage. Do the boost control with a MAC valve and control it with the aftermarket ECU of your choice, I use Link stuff on most of my builds with the G4x Storm as the minimum. I also wire a fuel pressure sensor and oil pressure sensor to the ECU in my installs. Use a decent intercooler, the better cores (ARE, PWR, Garrett, Vibrant, Plazmaman, Hypertune) work a lot better than the chinese stuff like Aeroflow. a 450x250-300 fits fairly well with custom end tanks to route the cooler pipes through next to the radiator Don't forget about the clutch and gearbox. These days I like the Uniclutch twinplate, Above 300whp you'll want to think about upgrading the 3rd and 4th gears in the box also with the SSC (Hollinger) gear set and install an LSD of your choice. If you're going to give it a hard time, you'll also want an oil cooler. I like the HKS thermostat type sandwich plates and setrab or mocal oil coolers with -10 speedflow fittings/lines (Chinese AN fittings neck down to a lot smaller internal diameter in their bends, not great for flow) You'll also want to think about brakes, Celica or Sportivo front calipers will bolt on with sportivo discs as a starting point. To have somewhere like Tunehouse do the work you'll want to budget somewhere between 20-40K
      CHA54 in Corolla / Corolla Sportivo Club
    7. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      I did the mathematics myself regarding costs vs benefits for fuel injector cleaner. I have changed from 91ULP to 95PULP and 98PULP. Price difference can be about 13 -20 cents. Compared to 91ULP, Premium quality fuel should have a better quality additive package designed to have superior engine cleaning capabilities so the engine can perform at their best.
      campbeam in Camry Club
    8. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      "Fuel injector cleaner is a waste of money" Only if you by the cheap crap if you use LiquMolly a German Product it does work and you won't waste your Money.
      Aussie Camry in Camry Club
    9. 0

      Camry Touring 2010 A/C Issues.

      Hi Guys, My Camry 2010 Touring just had a regas done on it and the next day for some reason it wasn't blowing cold air but the next day it is and now working with nice cold air BUT every now and then we can hear and feel a buzz for a few secounds and today while my sister took my car I could her like a mild knocking sound when stopped but goes away when driving off. Any idea what this could be and the A/C is always working now for now.
      Aussie Camry in Camry Club
    10. 6

      My Toys & Collectables

      Friday the 13th added
      L4WL3SS in Club Lounge
×
×
  • Create New...

Forums

News

Membership