KE70E Mods

[zeel_101]

Hi everyone, as of a couple of days ago I became the proud owner of a KE70E rolla. Like many 18yo guys I wish to get the best performance out of my car for the least possible money lol. Anyway if anyone could offer some advice about mods I could do on it that wouldd be awsome. So onto the car, ok its a KE70E with a 4k-c engine and its also a 4 spd manuel. It's completly stock except for a weber carby, hi performance leads and a bosch gt40 sports coil which were put in before I purchased the car. It has just recently had a new timing chain and clutch put in. Any advice is welcome as I'm usually a holden man and dont know much about toyota.

-=Jared=-

[CAP]

Welcome

You'll find most members here own the newer generation zz models so we don't really know too much about your model (except for rollamods)

However, checkout toymods.org, they'll be able to help you out much better there with info for your model.

Cheers.

[CHA54]

you can do lots of stuff with the KE70... I gutted mine and put decent gear into it.

www.rollaclub.com is the site to go to for the x70 rolla's.

My pics are here: http://www.rollamods.com/gallery/posv3/index.htm

Specs of mine are:

Specs of the car now:

-1981 KE70, Yellow.

-AE71 crossmember, steering rack & column, dash cluster, dash loom, shifter surround, heater box, front body loom modified for KE70 headlights and indicators

-TA63 Carina steering arms, suspension arms and struts converted to coilovers with Koni red inserts

-Cusco cambertops

-MA61 front brakes with slotted DBA rotor and EBC greenstuff pads

-AE86 T series LSD disc-brake rear end with AE86 Levin tailshaft

-S15 Brake Master Cylinder on AE71 booster

-Whiteline front and rear swaybars, adjustable panhard rod, strut brace.

-AE86 low king springs with KYB Gas commodore shocks in rear.

-Watanabe 15x7 rims sandblasted, painted and lip polished. 195/50/15 Wanli directional tyres

-Greddy electronic peak recall warning boost guage and electronic water temp guage moulded into dash cluster surround

-Smallport 4age with manifold cut and shut for RWD, bigport flat-style rear sensor housing for firewall clearance

-Standard Smallport clutch and flywheel with spigot bearing installed in crank

-Smallport 4age starter motor.

-Blitz K24 AE86 turbo kit with cast manifold and external gate

-Trust FMIC with modified end tanks for cooler pipes and headlight clearnace

-Mild steel mandrel bent, TIG welded cooler pipes

-Blitz BOV

-Cusco oil catch can

-K&N Extreme airfilter

-2.25" TIG welded Mandrel-bent exhaust with spiral resonator and offset-in/center-out rear muffler

-Bosch external fuel pump running off AE92 GTZ fuel pump electronics (fuel pump relay, circuit opening relay, resistor etc)

-Brass compression fittings on all steel fuel lines, flexible lines replaced with EFI hose

-AE92 GTZ 4agze injectors, coils, CAS, ECU, ignitor etc running the show

-Modified tacho drive board to work with 4agze ignitor (guide available)

-Alarm, central locking and EFI wiring integrated into existing car looms

-Davies Craig thermofan operating off AE92 fan relay installed in AE71 fuse box, actuated by AE92 fan switch in remote thermostat housing.

-Reconditioned AE86 Radiator

-modified AE92 accelerator cable

-AE71 pedalbox installed

-Autotechnica Steering wheel

-Jaycar 6.5" response speakers in rear shelf, Pioneer 4" in front stock locations

-Boot mounted battery

Mods still to complete:

-Installation of two Recaro seats

-Installation of headunit in lower center console

-Fit AE71 doors with integrated side mirrors

-Respray exterior in factory yellow with black doorframes

-tint windows

-Fit boost controller

[MAP81]

Hi zeel and welcome,

Check this out 4AGTE KE70

edit...

hahaha you beat me to it

Edited October 3, 2005 by MAP81

[CAP]

He's not called rollamods for nothing now is he :P

[CHA54]

MAP81 helps... if he say's it's a 12mm bolt, I grab the 14mm spanner etc... :P

[MAP81]

MAP81 helps... if he say's it's a 12mm bolt, I grab the 14mm spanner etc...  :P

←

:P

[CAP]

MAP81 helps... if he say's it's a 12mm bolt, I grab the 14mm spanner etc...  :P

←

:P

←

Then MAP81 laughs at rollamods when it was in fact a 12mm bolt

[MAP81]

Then MAP81 laughs at rollamods when it was in fact a 12mm bolt 

←

Nah I'm usually wrong