cruise control Question : ZZE122R corolla 2005 A/T Fitting after market Cruise Control

[lleeiz]

Hi, I want to fit a after market cruise control in my corolla 2005 Dec. It is ZZE122R, 1.8L, A/T, electronic throttle body control.

However, all the "How to video" on youtube are not same as my car. I had some photo attached. I only have 2 pins in that port and only 1 pin is actually ported out on the other side.

How can I fit it in the car? I know the black wire is ground. Where should I plug the red wire in? 

Don't laugh at me. I tried to plug the red one in the spare pin and the black one on the metal part of the steering wheel (I though it's ground). But when I press cruise control, the horn rang off.

[CHA54]

you need a different clockspring with the pins all populated.  You can't share the horn trigger

[lleeiz]

7 hours ago, CHA54 said:

you need a different clockspring with the pins all populated.  You can't share the horn trigger

Thank you for your help.

If I got a new clockspring, the ground wire for the horn is the only one actually ported out from the clockspring. Should I connect the red wire of the cruise control to some pin on ECU, or some other port in the car. 

[lleeiz]

My car is 1ZZ-FE. I cannot find the ECU port diagram for cruise control on my car.

[CHA54]

you will need to run 2 new wires from the body-side of the clockspring. One to the ECU and another to the engine ground loom (Brown wires that ground in the lug that bolts to the end of the head near the radiator hose connection).

I don't have a DBW 1zzfe diagram handy, but the 3zzfe is very similar and has a CCS pin in position 24 of the 35 pin ECU plug.  If you're lucky the ECU will be cruise control enabled and it might work.   You may also have to check if the cluster actually has a cruise light and that is wired to the ECU also.
 

Edited February 12, 2016 by CHA54

[lleeiz]

3 hours ago, CHA54 said:

you will need to run 2 new wires from the body-side of the clockspring. One to the ECU and another to the engine ground loom (Brown wires that ground in the lug that bolts to the end of the head near the radiator hose connection).

I don't have a DBW 1zzfe diagram handy, but the 3zzfe is very similar and has a CCS pin in position 24 of the 35 pin ECU plug.  If you're lucky the ECU will be cruise control enabled and it might work.   You may also have to check if the cluster actually has a cruise light and that is wired to the ECU also.
 

Thank you for your help. 

I found this on internet. But I don't know what 10 CCS means on the EUC box. Is that pin 10 of the 35 pin ECU plug?

[CHA54]

That's the non-drive-by-wire diagram.  Not applicable to your car.  It uses the external cruise control actuator motor like a cable throttle ZZT231 celica

[lleeiz]

56 minutes ago, CHA54 said:

That's the non-drive-by-wire diagram.  Not applicable to your car.  It uses the external cruise control actuator motor like a cable throttle ZZT231 celica

You are genius. Thanks a lot. 

[Sarki029]

On 2/12/2016 at 10:52 PM, CHA54 said:

you will need to run 2 new wires from the body-side of the clockspring. One to the ECU and another to the engine ground loom (Brown wires that ground in the lug that bolts to the end of the head near the radiator hose connection).

I don't have a DBW 1zzfe diagram handy, but the 3zzfe is very similar and has a CCS pin in position 24 of the 35 pin ECU plug.  If you're lucky the ECU will be cruise control enabled and it might work.   You may also have to check if the cluster actually has a cruise light and that is wired to the ECU also.
 

Would it be possible for you to post the rest of this wiring diagram? I can't seem to find it anywhere!

Thanks

[Tyce]

Hi, sorry for the late reply to this thread.

Did the cruise control work for you @lleeiz after installing the new clock spring, without needing to re-flash the ECU?

I have the same model corolla with the same issue.

Thanks and looking forward to your response.

[Adeel07]

I do that same as shown in the picture,  my cruise control  when i push on button once its just picked up Rpm and after that he left to rest position... 

[Olrolla06]

Sorry guys, I'm new to this club. @lleeiz have you found the solution yet? When I remove the 2 T30 screws I have the same connector as yours and there's no mounting holes for the cruise control stalk for my steering wheel. Just wondering if I go to the wreckers and get one similar steering wheel with the cruise control and also the clock spring and plug it in my car, will that work?