Aurion ZR6

Been there do that months ago, Xenon HID Kit Headlight Upgrade on Toyota Aurion

If you want the synthetic oil go for it, not that I wanted to go to synthetic oil, as the 10-30W is just as good or they would not be selling it, it is up to you hip pocket at what you want to spend. YES the instruction are on side of the box of the oil cartridge.

Toyota 10-30W for VVT engines. $28.50 for 5 litres.

At the front driver side of engine, you will need a special tool to remove the oil filter,as the Aurion has a cartridge and not a oil filter like most cars. The item is a tool with you attached to the bottom of the exterior of the filter body to gain access to the cartrdge which is housed inside. Part number for this tool is: 09228-06501 You will need 6.10 litres oil if the oil filter cartridge replaced.

Read here:http://au.toyotaownersclub.com/forums/inde...showtopic=13772 What is display once you select reverse: "CHECK SURROUNDINGS FOR SAFETY"

Easy put 12 volts via a switch to the red wire on plug H at rear of navigation unit. Look at attached picture. H plug has 3 wire only on it.

Make a new folder called it Aurion Manual Then download everything into this folder, including the "index.html" Then open your browser and click open file and point to this folder and click on "index.html" Look at attached file of the folder open from browser.

Will Winrar the whole collection together once I have the Powersteering.pdf Just a noticed the file will probably be over 266 megabyte. rar file for downloading? Is this to large for everyone to download?

It is a manufacturing fault, or the bracket on the floor it too low, which is bending down the centre console onto this bracket, then when you fit the centre console component into place, the tolarance between the surround and console are touching each other, which start the squeaking noise, as they are touching each other. I though the console was moving when you apply you left leg against the console, but what it was, you where distorting the console more by increasing the pressure of your leg against the console which increased the noise from the 2 plastic surface rubbing each other, in which you think to tighten the screw more, in if fact you are making in worse, and bending the console more. Taken me while to sort this out, but found what was causing the noise. Once you place the washers under the bracket to raise the console, (eg: 2-4mm) so you are straighting out the bend in it, (cause by the screw that are holding it down the console beside the gear selection). Once do, the centre console component is pressed into place without the 2 plastic surface rubbing each other around under the gear selection section.

HID installation of my Toyota Aurion ZR6 6000k lamps:http://hid.poirus.com.au/index.htm

Do you know if the OEM wiring is at the rear of your existing radio? because there are about 10 different pins required to run this type of unit!!! not worth the time, better off getting the after market Toyota dealer version, at least you know you are going to receive your car back with a navigation unit installed, and without all the hassles of sorting the wiring out, plugs etc.

Easy to fix might was the same a squeak noise while the vehicle moving, and coming for the gear lever. Remove centre console and add 2 washers under the screw on each side(between the bracket and plastic side wall of the console,) what happening is the console have been pulled down to far, and once the selector is installed (it rubs plastic surfaces together) which make the squeak noise. If you are a little lost, I can take some photos.

Link WAS down the last few days up now, as I just check it.

I see the problem the file I have in corrupted as I cannot see it as well. I have removed this file till someone can offer a working version of powersteering.pdf

Today I have modified my Selector gear Change in "S" Mode. Read the rest at my web site. I don't thing there any gain for this mod apart from, you are changing gears the right way compare to the factory OEM setup! Any feedback would be appreciated Selector Mod for changing Gear Quicker in "S" Mode

What wiring did you use to get the Alpine DVD unit to play on the OEM Navigation unit?

Have move my web site of the installation of HID 6000K to here:HID 6000K Installation Enjoy

Sorry for not following up on this as I had to draw up the drawing and here it is. How to conect the camera to the Navigation Unit. Download this camera from Polaris Rear Vision System look under Accessories And this cable below Any questions post here.

Removed Gpsace.

Intrusion bar Look in the bootm left side of the hole within the speaker. It is a 30mm white intrusion bar. Also here you go a picture edited from service manual. http://www.fileshost.com/en/file/30612/Int...on-bar-jpg.html

All FIXED! please check if it work please.

If you look in the post of ZR6 Speaker Upgrade you will notice in one of the photo's the side intrusion bar is shown through the speaker hole.

Spoke to my mate at Toytoa, and what happened to the TRD that blown the engine up was that the customer thought he was in quick shift -/+ and was not! The actual lever was in "D" for Drive and the customer pushed the lever into NETRUAL and the engine hit the rev limited to late as it was set to 6800rpm and did not catch the sudden revs of the engine, and peak the 9000 + mark and bang. The fix was Toyota reprogrammed the revs limiter to 6600 rpm now or something like this to pickup the instant of high rev peaks.

Uploaded an Index.html to use with your pdf's so it is easier to surf the pdf's pages. Just download and under pack into same folder as your pdf's and double click the index.html to use. Cheers Drew