Jump to content


removing spoiler

goppy

By goppy
in Aurion / TRD Aurion Club

 Share

Recommended Posts

goppy Community Regular

goppy

Posted
Posted (edited)

has anyone removed there spoiler? if so are there any huge ugly holes? i've always said removing the spoiler will make people look twice but im not sure how to.

heres an example of one with the spoiler post-5294-1233451613_thumb.jpg and one without post-5294-1233451552_thumb.jpg, sorry about the picture theft eSEXSIX

thanks goppy

Edited by goppy

BONDIE Mentor

BONDIE

Posted
Posted (edited)
has anyone removed there spoiler? if so are there any huge ugly holes? i've always said removing the spoiler will make people look twice but im not sure how to.

heres an example of one with the spoiler post-5294-1233451613_thumb.jpg and one without post-5294-1233451552_thumb.jpg, sorry about the picture theft eSEXSIX

thanks goppy

Maaan that colour is crazy hot. It reminds me of a movie i used to watch as a young fella, I think it was called "COBRA", the one with Sly Stallone with that crazy silver car. (Some of you ol fellas will know the movie)

Looks good without the spoiler, more sleek looking.

Edited by BONDIE
goppy Community Regular

goppy

Posted
  • Author
Posted
has anyone removed there spoiler? if so are there any huge ugly holes? i've always said removing the spoiler will make people look twice but im not sure how to.

heres an example of one with the spoiler post-5294-1233451613_thumb.jpg and one without post-5294-1233451552_thumb.jpg, sorry about the picture theft eSEXSIX

thanks goppy

Maaan that colour is crazy hot. It reminds me of a movie i used to watch as a young fella, I think it was called "COBRA", the one with Sly Stallone with that crazy silver car. (Some of you ol fellas will know the movie)

Looks good without the spoiler, more sleek looking.

i think there is a colour very colse to it, yea i agree, no anything about removing? or nah?

DJKOR Grand Master

DJKOR

Posted
Posted

I'm not sure if anyone here has removed their spoiler yet. Well, I haven't heard of it happening yet anyways. Removing the spoiler will be relatively easy as you just need to take the lining off the inside of the boot lid, loosen a few nuts that hold the spoiler in, then pull the spoiler off. Then you have the fun task of filling in the holes that you now have in the lid of your boot, then getting it pained and blended in.

But a Sportivo without a spoiler? I reckon it would look a little bit too odd. You would at least want a duck tail to create balance in combination with the rear skirt.

Edit: On closer inspection, the spoiler is held in by 1 nut on each side, and one plastic clip. This will mean you will have a total of five holes to patch on your boot lid.

dsc03359ho6.th.jpg dsc03360bt3.th.jpg

And on the left hand side here, you can see the size of the hole for the cable loom:

dsc03366jr3.th.jpg


goppy Community Regular

goppy

Posted
  • Author
Posted
I'm not sure if anyone here has removed their spoiler yet. Well, I haven't heard of it happening yet anyways. Removing the spoiler will be relatively easy as you just need to take the lining off the inside of the boot lid, loosen a few nuts that hold the spoiler in, then pull the spoiler off. Then you have the fun task of filling in the holes that you now have in the lid of your boot, then getting it pained and blended in.

But a Sportivo without a spoiler? I reckon it would look a little bit too odd. You would at least want a duck tail to create balance in combination with the rear skirt.

Edit: On closer inspection, the spoiler is held in by 1 nut on each side, and one plastic clip. This will mean you will have a total of five holes to patch on your boot lid.

dsc03359ho6.th.jpg dsc03360bt3.th.jpg

And on the left hand side here, you can see the size of the hole for the cable loom:

dsc03366jr3.th.jpg

thanks daryl, after what youve told me i'll forget about removing it lol

goppy Community Regular

goppy

Posted
  • Author
Posted
Wingless ftw!

Or get a presara :P

yes wingless ftw for sure, i would go perserra but its gotta have the sportivo body kit :)

Freddo Mentor

Freddo

Posted
Posted
Wingless ftw!

Or get a presara :P

yes wingless ftw for sure, i would go perserra but its gotta have the sportivo body kit :)

Get someone without a wing to do a bootswap maybe?

I was going to get an aftermarket sportivo kit but will just get the lip kit from Thailand instead.

All sticks need is to be dumped on 19/20s and it looks good. De-wing to be different.

SecaBoy Grand Master

SecaBoy

Posted
Posted

its not that expensive to get the holes filled in and the boot lid resprayed...

my old wrx only cost me about $240 from memory...

Freddo Mentor

Freddo

Posted
Posted
its not that expensive to get the holes filled in and the boot lid resprayed...

my old wrx only cost me about $240 from memory...

Or go the rubber grommets for the ardcore racer look.

KevO Grand Master

KevO

Posted
Posted

i reckon it would look better if you left the spoiler on, but thats just an opinion.

to me, itll just seem empty to have a spoilerless aurion zr6

BONDIE Mentor

BONDIE

Posted
Posted
bondie my good man!! wanna boot swap? lol

Naaaaa, sorry brother, Thats one of the reasons i chose the car ive got, not a big fan of raised spoilers. No offence, personal opinion. Don't mind the little lip/duck tails though. Im going for the more of a sleek look.

Cheers, anyways.

apg39 Veteran

apg39

Posted
Posted

I think the Aurions look better without the big wing....but I've never liked big wings. Duck tail or lower wing would be good but the current range available isnt very attractive.

Another thing to note too - if Sportivo's remove the wing you'll need a 3rd brakelight. I cant remember what the ATX/Presara/Prodigy 3rd light looks like but Im imagining it would be as easy as getting the ATX/Presara/Prodigy 3rd light & re-running the wires to the parcel shelf. Either that or make a custom one...

ATX/Prodigy/Presara owners who want a wing will prob just have to splice the 3rd brake light wire thats there or completely unhook it & extend to the wing.

Not as easy as bolt on & take off.

DJKOR Grand Master

DJKOR

Posted
Posted
Another thing to note too - if Sportivo's remove the wing you'll need a 3rd brakelight. I cant remember what the ATX/Presara/Prodigy 3rd light looks like but Im imagining it would be as easy as getting the ATX/Presara/Prodigy 3rd light & re-running the wires to the parcel shelf. Either that or make a custom one...

Would definitley need to be a little bit of a custom job. Because the rear brake lights are LED and don't need replacing, the spoiler-less Aurion's have the third brake light moulded into the parcel shelf for that clean look.

AUR30N Veteran

AUR30N

Posted
Posted
bondie my good man!! wanna boot swap? lol

Naaaaa, sorry brother, Thats one of the reasons i chose the car ive got, not a big fan of raised spoilers. No offence, personal opinion. Don't mind the little lip/duck tails though. Im going for the more of a sleek look.

Cheers, anyways.

Bondie - hence why Iam putting a duck tail lip / not into big spoilers that look like you could push your car like a shopping trolley :-)

Azza73

notfromthere Collaborator

notfromthere

Posted
Posted
Maaan that colour is crazy hot. It reminds me of a movie i used to watch as a young fella, I think it was called "COBRA", the one with Sly Stallone with that crazy silver car. (Some of you ol fellas will know the movie)

1950 Ford Mercury Monterey

http://img519.imageshack.us/img519/3432/50...montereyqh3.jpg

http://img519.imageshack.us/img519/483/50m...reycobrafh6.jpg

But if I had my choice;

http://img382.imageshack.us/img382/5360/68...echargered8.jpg

http://img164.imageshack.us/img164/7167/68...charger1pc2.jpg

Anyway, to stay 'on' topic, I think it would look pretty slick without the spoiler. And the colour you have chosen would be sweet but remember to get the spoiler painted the same colour as the car just incase you want it back on.

  • 11 months later...
VF-X Grand Master

VF-X

Posted
Posted (edited)

A revival of an old topic..

What do I use to cover the holes from the spoiler?

Not that I want to remove the spoiler, but I was thinking of installing the TRD rear wing to the sportivo. I just found out that the holes don't fit, FAIL BIG TIME.

its not that expensive to get the holes filled in and the boot lid resprayed...

my old wrx only cost me about $240 from memory...

I wasn't told $240..Not even close. =(

Any cheap DIY?

Or any1 wanna boot swap? xDDDDDD

Edited by VF-X
SecaBoy Grand Master

SecaBoy

Posted
Posted

mate, go to a few different paint/panel shops...

it should cost you no more than $350 these days...

if you were in brissie, i could point you in the right direction... :(

VF-X Grand Master

VF-X

Posted
Posted

Would it make sense to make changes in the wing itself instead of the boot? I mean, it's a zr6. It should have the elements of ZR..

And would make much more sense, and easier..

SecaBoy Grand Master

SecaBoy

Posted
Posted

sorry man, but im confused as to what you're trying to do...

you obviously have a ZR6 now. right?

and you're trying to install the TRD wing on your boot?

have i understood you correctly?

VF-X Grand Master

VF-X

Posted
Posted

Yea.. My car is a ZR and trying to install TRD rear wing. U reckon it's easier to re-position the screw on the wing so it fitsinto the ZR?

SecaBoy Grand Master

SecaBoy

Posted
Posted

ah ok...

well, i've never compared the mounting holes for the two wings... but one would assume that they are exactly the same considering the fact the car started its life off as a sportivo..

maybe dave/daryl has more to comment on this as they seem to have taken random things apart at times... :lol:

would it help you if i take my wing off and take measurements/pictures of the holes in the boot lid?

i actually want to take the top part of my wing off and see what it looks like with just the 'duck tail' part of it... depends what time i get home tonight, i might give it a go... :)

VF-X Grand Master

VF-X

Posted
Posted
ah ok...

well, i've never compared the mounting holes for the two wings... but one would assume that they are exactly the same considering the fact the car started its life off as a sportivo..

That was me.. :(

would it help you if i take my wing off and take measurements/pictures of the holes in the boot lid?

Nah man, dun worry. How did u think I knew the mounting holes are different to begin with anw? :lol:

I can make measurements from the wing itself. But If u do take it off, wouldn't hurt to see some pics. :P

i actually want to take the top part of my wing off and see what it looks like with just the 'duck tail' part of it... depends what time i get home tonight, i might give it a go... :)

I bet it's gonna be a bit dull, considering ur bumper is TRD, without wing and just ducktail, I'll be like err...

Do take the ducktail off and see how the rear wing go by itself.. That'll help my dcision :lol: :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing



  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 10

      Android auto

      OK. Does any of Toyota's advertising material mention Android Auto? If so then kick up a stink, with Toyota management, about misrepresentation and false advertising, reminding them of the hefty fines. Herb
      ozieagle in RAV4 Club
    2. 0

      E160 Corolla fielder suspension

      Does any one know if the trd sportivo suspension for the 2017 facelift corolla fielder fits the 2013 prefacelift version? Is the chassis the same? Thanks for the help.
      jay886 in Corolla / Corolla Sportivo Club
    3. 0

      Remote start

      What bipass do i need for immobilliser to install a remote start to my 2021 hiace
      chris mc1 in Audio/Video/Electronics
    4. 1

      1999 Camry Driver's door locking hatch issue

      It's possible that it could be something fouling or dirt build up, dry, or a broken mechanism, so have a look and give the mechanism some lubrication, most likely though, it'll be the actuator. I found one for a good price on Ebay, $25 delivered: Front Door Lock Actuator Right Side For Toyota Camry 1997-2001 | eBay
      Monad in Camry Club
    5. 0

      Query about the correct rotors for 2006 ACV40 Camry.

      Hi, I'm looking at a set of front rotors for an ACV40 2006, 2.4L Camry. I got a good price on some RDA's at Sparesbox. However both RDA8112 and RDA7686 show as for my car and I'm wondering what the difference is and if there were changes to the rotors during the model production. So does anyone know which rotor is the correct one? Many thanks in advance.
      Monad in Camry Club
    6. 10

      Android auto

      It's a simple solution though? Already laying down 60k for a RAV4, so what's another 1k on a phone to make everything work seamlessly? 👍
      L4WL3SS in RAV4 Club
    7. 10

      Android auto

      Your solution is akin to suggesting that switching to a different car manufacturer would resolve the issue. However, not everyone shares the same enthusiasm for using an iPhone as you do.
      Equi28 in RAV4 Club
    8. 1

      Turboed Corolla Overbuilt?

      that engine will be fine, the rods are the main thing to be concerned about. The 2860 is a decent turbo for the 1zz but in this day and age I'd go for a G25-550. The injectors might be on the small side, we run DW1000's. You need a full length injector, the shorter injectors with adaptors like ID1050x dont fit the 1zz head. You don't need an aftermarket intake manifold, if you do go down that path, avoid the CNC innovations unit, it's garbage. Do the boost control with a MAC valve and control it with the aftermarket ECU of your choice, I use Link stuff on most of my builds with the G4x Storm as the minimum. I also wire a fuel pressure sensor and oil pressure sensor to the ECU in my installs. Use a decent intercooler, the better cores (ARE, PWR, Garrett, Vibrant, Plazmaman, Hypertune) work a lot better than the chinese stuff like Aeroflow. a 450x250-300 fits fairly well with custom end tanks to route the cooler pipes through next to the radiator Don't forget about the clutch and gearbox. These days I like the Uniclutch twinplate, Above 300whp you'll want to think about upgrading the 3rd and 4th gears in the box also with the SSC (Hollinger) gear set and install an LSD of your choice. If you're going to give it a hard time, you'll also want an oil cooler. I like the HKS thermostat type sandwich plates and setrab or mocal oil coolers with -10 speedflow fittings/lines (Chinese AN fittings neck down to a lot smaller internal diameter in their bends, not great for flow) You'll also want to think about brakes, Celica or Sportivo front calipers will bolt on with sportivo discs as a starting point. To have somewhere like Tunehouse do the work you'll want to budget somewhere between 20-40K
      CHA54 in Corolla / Corolla Sportivo Club
    9. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      I did the mathematics myself regarding costs vs benefits for fuel injector cleaner. I have changed from 91ULP to 95PULP and 98PULP. Price difference can be about 13 -20 cents. Compared to 91ULP, Premium quality fuel should have a better quality additive package designed to have superior engine cleaning capabilities so the engine can perform at their best.
      campbeam in Camry Club
    10. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      "Fuel injector cleaner is a waste of money" Only if you by the cheap crap if you use LiquMolly a German Product it does work and you won't waste your Money.
      Aussie Camry in Camry Club
×
×
  • Create New...

Forums

News

Membership