Jump to content

Side Strips

Evo7

By Evo7
in Corolla / Corolla Sportivo Club

 Share

Recommended Posts

Evo7 Grand Master

Evo7

Posted
Posted

Take off the side strips on a corolla (not sportivo), and get them painted, and reinstalled back on the car.

Or are they sprayed when still on the car?

Also, what do u use to reinstall them?

is it some sort of special glue or what?

Thanks

Evo
Evo7 Grand Master

Evo7

Posted
  • Author
Posted

Does anyone have a pic of how they look removed?


Evo7 Grand Master

Evo7

Posted
  • Author
Posted

im not sure if it would look better or not though.... what protects the car from getting scratched?

also, i have noticed that the new model corolla hasn't got the side strip either??? <_<

SQU-47N Experienced

SQU-47N

Posted
Posted

If u spray them on the car make sure u cover whole car to prevent over spray, if not be careful taking them off as they can bend. Use urathane or something like that to re-attatch them. My vote do it on the car. Just make sure ur paint is a exact match. Hope that helps :D

Brad! Grand Master

Brad!

Posted
Posted

The problem that i have heard is the door becomes louder when shutting them without these on.

Solution?

Take off your door trim and place them inside - was reading about it on 9th Gen.

The cost and effort to get them painted will be more then fixing a scratch if you get one due to not having the strips.

Kenneth Grand Master

Kenneth

Posted
Posted
The problem that i have heard is the door becomes louder when shutting them without these on.

Solution?

Take off your door trim and place them inside - was reading about it on 9th Gen.

The cost and effort to get them painted will be more then fixing a scratch if you get one due to not having the strips.

yes thts correct.. it gives it a bad hollow noise on the front door especially.. (driver side from my experience but nothing i cant deal without) so yeh

and jeremy i was gna post it up neway but yeh :D hehe all goes well

chicken Grand Master

chicken

Posted
Posted

I am actually getting my body moulds painted tomorrow, the guy removed them on my car today (which i was reluctant to do but I'm trusting him on this...) to get them painted with my side skirts. So now im driving around with the sticky residue left on the car haha. The guy said you can paint them while on the car but it won't be as good but can be done. I was quoted $82.5 per body mould/door which was painting while still on the car from a different smash repairer.

wil_rolla Mentor

wil_rolla

Posted
Posted

i was going to paint the side strips aswell, but then figured if i paint them i also have to paint the door handles too..

so what i did was i took them off to see how i liked it, if i didn't like how they looked then i could always paint them and stick them back on anyways.. but the end result was they stayed off... looks much cleaner and smooth..

the easiest way to take them off is by using some thin fishing wire and a hair dryer, but the glue is a pain to get off no matter what you use..

chicken Grand Master

chicken

Posted
Posted
i was going to paint the side strips aswell, but then figured if i paint them i also have to paint the door handles too..

so what i did was i took them off to see how i liked it, if i didn't like how they looked then i could always paint them and stick them back on anyways.. but the end result was they stayed off... looks much cleaner and smooth..

the easiest way to take them off is by using some thin fishing wire and a hair dryer, but the glue is a pain to get off no matter what you use..

Yeah I was thinking about painting the door handles too but that would be too expensive, i might replace them with colour coded handles from another car at the wreckers in the future.

Evo7 Grand Master

Evo7

Posted
  • Author
Posted
i was going to paint the side strips aswell, but then figured if i paint them i also have to paint the door handles too..

so what i did was i took them off to see how i liked it, if i didn't like how they looked then i could always paint them and stick them back on anyways.. but the end result was they stayed off... looks much cleaner and smooth..

the easiest way to take them off is by using some thin fishing wire and a hair dryer, but the glue is a pain to get off no matter what you use..

Yeah I was thinking about painting the door handles too but that would be too expensive, i might replace them with colour coded handles from another car at the wreckers in the future.

Yeah, well i decided that i'll leave them on cause i prefer the look of them, so don't tell me otherwise :o

Evo

Browny Collaborator

Browny

Posted
Posted
The problem that i have heard is the door becomes louder when shutting them without these on.

Solution?

Take off your door trim and place them inside - was reading about it on 9th Gen.

The cost and effort to get them painted will be more then fixing a scratch if you get one due to not having the strips.

yes thts correct.. it gives it a bad hollow noise on the front door especially.. (driver side from my experience but nothing i cant deal without) so yeh

and jeremy i was gna post it up neway but yeh :D hehe all goes well

Ken, did you just pull them off then clean off the glue? My car is black so they dont look so bad but after reading this thread i think i mite take them off lol. the drivers door has a big chip in the strip which they did at the smash repairs....was not happy!! I was not sure if they were painted underneath with the same colour as the car

Danthuyer Grand Master

Danthuyer

Posted
Posted

Simply grab one end of the strip and pull back away from the car at a 45deg angle in once nice slow motion. You are best to leave the car out in the sun on a a nice warm day to assist with the removal, as the heat will make the glue less brittle.

Once the strips are off clean the area (normal car washing technique) then use eucalyptus oil to remove any sticky bits left on the doors.

The doors look V sexy once complete. I first notice the corolla wagons in the UK with this from factory and promptly did this to my old roller when i returned back to aus. One of the eaiest ways to make the ext look sexy (thank *** the doors dont have any channels on them)

have fun :)

and1 Grand Master

and1

Posted
Posted

This is what it looks like on a facelift.

IMG_0323.jpg

Browny Collaborator

Browny

Posted
Posted
This is what it looks like on a facelift.

IMG_0323.jpg

Mate that looks really awesome. Im gunna pull mine off this weekend now!!

TRDYUS Grand Master

TRDYUS

Posted
Posted (edited)

Does it leave any adhesive or markings behind?

So it's just a clean removal...

Edited by TRDYUS
and1 Grand Master

and1

Posted
Posted
What happened to your bonnet?

I raised it ;) .. Track style lol

chicken Grand Master

chicken

Posted
Posted (edited)
Simply grab one end of the strip and pull back away from the car at a 45deg angle in once nice slow motion. You are best to leave the car out in the sun on a a nice warm day to assist with the removal, as the heat will make the glue less brittle.

Once the strips are off clean the area (normal car washing technique) then use eucalyptus oil to remove any sticky bits left on the doors.

The doors look V sexy once complete. I first notice the corolla wagons in the UK with this from factory and promptly did this to my old roller when i returned back to aus. One of the eaiest ways to make the ext look sexy (thank *** the doors dont have any channels on them)

have fun :)

Thats very nice especially with the sideskirts on, very clean. is that condensation inside the headlight lens?

TRDYUS, I had adhesive left on the car after mine was taken off, but that was a rushed job. follow Danthuyer's method and you should be fine.

Edited by chicken
and1 Grand Master

and1

Posted
Posted
Simply grab one end of the strip and pull back away from the car at a 45deg angle in once nice slow motion. You are best to leave the car out in the sun on a a nice warm day to assist with the removal, as the heat will make the glue less brittle.

Once the strips are off clean the area (normal car washing technique) then use eucalyptus oil to remove any sticky bits left on the doors.

The doors look V sexy once complete. I first notice the corolla wagons in the UK with this from factory and promptly did this to my old roller when i returned back to aus. One of the eaiest ways to make the ext look sexy (thank *** the doors dont have any channels on them)

have fun :)

Thats very nice especially with the sideskirts on, very clean. is that condensation inside the headlight lens?

TRDYUS, I had adhesive left on the car after mine was taken off, but that was a rushed job. follow Danthuyer's method and you should be fine.

Yes it is. I don't know why its happening now. Never happened in winter.

Brad! Grand Master

Brad!

Posted
Posted

Did this this morning!!

Slowly pulled it off starting at the pointy end for each one (4).

When i pulled them off i went slow enough to keep most of the gunk on the strip.

What was left came off beuatifully with clay ;)

Will get pictures up soon to show you what Black Facelift looks like!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing



  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 0

      E160 Corolla fielder suspension

      Does any one know if the trd sportivo suspension for the 2017 facelift corolla fielder fits the 2013 prefacelift version? Is the chassis the same? Thanks for the help.
      jay886 in Corolla / Corolla Sportivo Club
    2. 0

      Remote start

      What bipass do i need for immobilliser to install a remote start to my 2021 hiace
      chris mc1 in Audio/Video/Electronics
    3. 1

      1999 Camry Driver's door locking hatch issue

      It's possible that it could be something fouling or dirt build up, dry, or a broken mechanism, so have a look and give the mechanism some lubrication, most likely though, it'll be the actuator. I found one for a good price on Ebay, $25 delivered: Front Door Lock Actuator Right Side For Toyota Camry 1997-2001 | eBay
      Monad in Camry Club
    4. 0

      Query about the correct rotors for 2006 ACV40 Camry.

      Hi, I'm looking at a set of front rotors for an ACV40 2006, 2.4L Camry. I got a good price on some RDA's at Sparesbox. However both RDA8112 and RDA7686 show as for my car and I'm wondering what the difference is and if there were changes to the rotors during the model production. So does anyone know which rotor is the correct one? Many thanks in advance.
      Monad in Camry Club
    5. 9

      Android auto

      It's a simple solution though? Already laying down 60k for a RAV4, so what's another 1k on a phone to make everything work seamlessly? 👍
      L4WL3SS in RAV4 Club
    6. 9

      Android auto

      Your solution is akin to suggesting that switching to a different car manufacturer would resolve the issue. However, not everyone shares the same enthusiasm for using an iPhone as you do.
      Equi28 in RAV4 Club
    7. 1

      Turboed Corolla Overbuilt?

      that engine will be fine, the rods are the main thing to be concerned about. The 2860 is a decent turbo for the 1zz but in this day and age I'd go for a G25-550. The injectors might be on the small side, we run DW1000's. You need a full length injector, the shorter injectors with adaptors like ID1050x dont fit the 1zz head. You don't need an aftermarket intake manifold, if you do go down that path, avoid the CNC innovations unit, it's garbage. Do the boost control with a MAC valve and control it with the aftermarket ECU of your choice, I use Link stuff on most of my builds with the G4x Storm as the minimum. I also wire a fuel pressure sensor and oil pressure sensor to the ECU in my installs. Use a decent intercooler, the better cores (ARE, PWR, Garrett, Vibrant, Plazmaman, Hypertune) work a lot better than the chinese stuff like Aeroflow. a 450x250-300 fits fairly well with custom end tanks to route the cooler pipes through next to the radiator Don't forget about the clutch and gearbox. These days I like the Uniclutch twinplate, Above 300whp you'll want to think about upgrading the 3rd and 4th gears in the box also with the SSC (Hollinger) gear set and install an LSD of your choice. If you're going to give it a hard time, you'll also want an oil cooler. I like the HKS thermostat type sandwich plates and setrab or mocal oil coolers with -10 speedflow fittings/lines (Chinese AN fittings neck down to a lot smaller internal diameter in their bends, not great for flow) You'll also want to think about brakes, Celica or Sportivo front calipers will bolt on with sportivo discs as a starting point. To have somewhere like Tunehouse do the work you'll want to budget somewhere between 20-40K
      CHA54 in Corolla / Corolla Sportivo Club
    8. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      I did the mathematics myself regarding costs vs benefits for fuel injector cleaner. I have changed from 91ULP to 95PULP and 98PULP. Price difference can be about 13 -20 cents. Compared to 91ULP, Premium quality fuel should have a better quality additive package designed to have superior engine cleaning capabilities so the engine can perform at their best.
      campbeam in Camry Club
    9. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      "Fuel injector cleaner is a waste of money" Only if you by the cheap crap if you use LiquMolly a German Product it does work and you won't waste your Money.
      Aussie Camry in Camry Club
    10. 0

      Camry Touring 2010 A/C Issues.

      Hi Guys, My Camry 2010 Touring just had a regas done on it and the next day for some reason it wasn't blowing cold air but the next day it is and now working with nice cold air BUT every now and then we can hear and feel a buzz for a few secounds and today while my sister took my car I could her like a mild knocking sound when stopped but goes away when driving off. Any idea what this could be and the A/C is always working now for now.
      Aussie Camry in Camry Club
×
×
  • Create New...

Forums

News

Membership