Jump to content


diy rear badge gone wrong

ptagna

By ptagna
in Inside and Out

 Share

Recommended Posts

ptagna Proficient

ptagna

Posted
Posted

hey guys , some time ago i removed my rear toyota badge and decided to spray it matte black. and to put it on back on i used some epoxy to stick it back on .

being scared that the badge might fall off i used some sticky tape to hold it. but when i removed the sticker tape the paint came off it as well <_< .

so i decided to put some sticky tape around it and spray the badge while its on my car and missed to sticky tape some bits in between the badges.

now at the moment in the middle of the toyota badge theres bit of matte black overspray -.- .

my question is how would i remove the badge ? heat gun and pill it off?

also how would i remove the overspray ? sand it down and cut and polish?

thanks in advance guys !
Kenshin X Grand Master

Kenshin X

Posted
Posted

hey guys , some time ago i removed my rear toyota badge and decided to spray it matte black. and to put it on back on i used some epoxy to stick it back on .

being scared that the badge might fall off i used some sticky tape to hold it. but when i removed the sticker tape the paint came off it as well <_< .

so i decided to put some sticky tape around it and spray the badge while its on my car and missed to sticky tape some bits in between the badges.

now at the moment in the middle of the toyota badge theres bit of matte black overspray -.- .

my question is how would i remove the badge ? heat gun and pill it off?

also how would i remove the overspray ? sand it down and cut and polish?

thanks in advance guys !

i'm sorry but let me say... LOL first. OK thats over and done with...

first what u can do is get a good quality cut and polish and a clay bar and see if u can get the over spray off... dont try and get the emblem of again. u will cause yourself alot of headf#$ks later on.

u can try the heat gun if u REALLY wanna take the emblem off but i think u'll deform the emblem before you can soften the glue enough to take it off.

KIRIUS Veteran

KIRIUS

Posted
Posted

laugh.gif

LOL

sorry, im with himura-san... the initial overwhelming action to lol was too great.

Not laughing at you specifically though, ive been there too, done stupid similar stuff its all part of learning! cool.gif

put up a pic sometime of it all cleaned up black, could be quite interesting ^_^

Good luck!

DJKOR Grand Master

DJKOR

Posted
Posted

You have kind of made things a little difficult for yourself here if you want to remove that badge. One way or another, if you need the badge removed, just prepare yourself to fix the paint around and behind it. There is a possibility that this may get damaged. Heat would be your only option really and even still, it's not going to be easy.

You may just be better off leaving it on and using touch-up paint to correct what you need to unless you are willing to accept the damage that may occur to your paint underneath during removal.


arc Mentor

arc

Posted
Posted

What DJKOR said, if you take that badge off all the paint around and under that badge is gonna rip off with it. Take a photo and upload it so we can see what were working with. For inside the badge you going to have to get a fine brush and some touch up paint.

ptagna Proficient

ptagna

Posted
  • Author
Posted

might just sand down the inside so its all smooth again, any recommendations of which sand paper ? how rough etc.

i was thinking of respraying it to gloss back (ill be more careful this time <_< ) should i sand down the badge again ?

was reading one of the diys before anyone in melbourne know where to get the plastidip thing ? or any better ideas to redo the badge .

also this is what it looks like atm :angry:

post-18244-0-48145300-1317697985_thumb.j

arc Mentor

arc

Posted
Posted

Is that eating the paint and rusting?

ptagna Proficient

ptagna

Posted
  • Author
Posted

Is that eating the paint and rusting?

nah i think thats the epoxy <_<

but ill double check again didnt notice that till now .

  • 2 weeks later...
ptagna Proficient

ptagna

Posted
  • Author
Posted (edited)

quick update guys.

just bought mothers clay bar and tried using it on the overspray but doesnt seem to work? what exactly does the clay bar do and how would you use it?

i tried it on grimes and it works perfect.

also i got meguiars scratch x 2.0.

was thinking of just sanding it down and using touch up paint to fix it up.

any tips ?

Edited by ptagna
trentmeyer23 Grand Master

trentmeyer23

Posted
Posted

Just STOP...Stop and think, can I do this? To be honest I think you should take it to a professional before you do more damage.

dyslexik Grand Master

dyslexik

Posted
Posted

Should of just bought a black Toyota camry emblem. If u wanna take that badge off, use a fishing line or dental floss. Then use 'De-Solv-it' citrus spray to remove the adhesive residue. Try using a bit of turps on a cloth to remove your overspray on the panel.

ptagna Proficient

ptagna

Posted
  • Author
Posted

how are things going..? im scared for your car =S

haha yeah im scared too :( . i dont wanna touch it might just get a quote on how much to fix it up.

any clue how much it would costs :S

jeffy Grand Master

jeffy

Posted
Posted

how are things going..? im scared for your car =S

haha yeah im scared too :( . i dont wanna touch it might just get a quote on how much to fix it up.

any clue how much it would costs :S

$100-$200 ?

Since its the whole boot panel... labour will cost an arm and a leg for you imo (thinking that the panel beater does it right)

Andrew357 Grand Master

Andrew357

Posted
Posted

A full boot respray with sanding + blending will cost around $250.

johnnieboi Grand Master

johnnieboi

Posted
Posted

If your in Melb i can do it for you. Just get the right rear badge for your car at Toyota as it comes with the double sided tape for easier mounting. I sand it back and put 2 coats of primer then 3 coats of matt black paint.

Heres how mine turned out.

post-10034-0-22099800-1319060981_thumb.j

LFT-OOF Veteran

LFT-OOF

Posted
Posted

If your in Melb i can do it for you. Just get the right rear badge for your car at Toyota as it comes with the double sided tape for easier mounting. I sand it back and put 2 coats of primer then 3 coats of matt black paint.

Heres how mine turned out.

post-10034-0-22099800-1319060981_thumb.j

i think he needs more than just the badge done definitely a respray on the boot

Andrew357 Grand Master

Andrew357

Posted
Posted

i think he needs more than just the badge done definitely a respray on the boot

At minimum a touch up guy to come round, remove the emblem and do his job. Given the cost of them however, it's probably worth paying the extra for a complete respray.

LFT-OOF Veteran

LFT-OOF

Posted
Posted

i think he needs more than just the badge done definitely a respray on the boot

At minimum a touch up guy to come round, remove the emblem and do his job. Given the cost of them however, it's probably worth paying the extra for a complete respray.

Yeh you never know they might be able to salvage it hope for the best just the epoxy scares me because once it sticks its stuck and its over some of the paint... if a touch up guy can do it i would be kissing his feet you will be a bit cheaper than getting it resprayed and less time consuming as you will lose your car for a fews days

ptagna Proficient

ptagna

Posted
  • Author
Posted (edited)

it looked like this before it got ruined. :(

Edited by ptagna

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing



  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 0

      E160 Corolla fielder suspension

      Does any one know if the trd sportivo suspension for the 2017 facelift corolla fielder fits the 2013 prefacelift version? Is the chassis the same? Thanks for the help.
      jay886 in Corolla / Corolla Sportivo Club
    2. 0

      Remote start

      What bipass do i need for immobilliser to install a remote start to my 2021 hiace
      chris mc1 in Audio/Video/Electronics
    3. 1

      1999 Camry Driver's door locking hatch issue

      It's possible that it could be something fouling or dirt build up, dry, or a broken mechanism, so have a look and give the mechanism some lubrication, most likely though, it'll be the actuator. I found one for a good price on Ebay, $25 delivered: Front Door Lock Actuator Right Side For Toyota Camry 1997-2001 | eBay
      Monad in Camry Club
    4. 0

      Query about the correct rotors for 2006 ACV40 Camry.

      Hi, I'm looking at a set of front rotors for an ACV40 2006, 2.4L Camry. I got a good price on some RDA's at Sparesbox. However both RDA8112 and RDA7686 show as for my car and I'm wondering what the difference is and if there were changes to the rotors during the model production. So does anyone know which rotor is the correct one? Many thanks in advance.
      Monad in Camry Club
    5. 9

      Android auto

      It's a simple solution though? Already laying down 60k for a RAV4, so what's another 1k on a phone to make everything work seamlessly? 👍
      L4WL3SS in RAV4 Club
    6. 9

      Android auto

      Your solution is akin to suggesting that switching to a different car manufacturer would resolve the issue. However, not everyone shares the same enthusiasm for using an iPhone as you do.
      Equi28 in RAV4 Club
    7. 1

      Turboed Corolla Overbuilt?

      that engine will be fine, the rods are the main thing to be concerned about. The 2860 is a decent turbo for the 1zz but in this day and age I'd go for a G25-550. The injectors might be on the small side, we run DW1000's. You need a full length injector, the shorter injectors with adaptors like ID1050x dont fit the 1zz head. You don't need an aftermarket intake manifold, if you do go down that path, avoid the CNC innovations unit, it's garbage. Do the boost control with a MAC valve and control it with the aftermarket ECU of your choice, I use Link stuff on most of my builds with the G4x Storm as the minimum. I also wire a fuel pressure sensor and oil pressure sensor to the ECU in my installs. Use a decent intercooler, the better cores (ARE, PWR, Garrett, Vibrant, Plazmaman, Hypertune) work a lot better than the chinese stuff like Aeroflow. a 450x250-300 fits fairly well with custom end tanks to route the cooler pipes through next to the radiator Don't forget about the clutch and gearbox. These days I like the Uniclutch twinplate, Above 300whp you'll want to think about upgrading the 3rd and 4th gears in the box also with the SSC (Hollinger) gear set and install an LSD of your choice. If you're going to give it a hard time, you'll also want an oil cooler. I like the HKS thermostat type sandwich plates and setrab or mocal oil coolers with -10 speedflow fittings/lines (Chinese AN fittings neck down to a lot smaller internal diameter in their bends, not great for flow) You'll also want to think about brakes, Celica or Sportivo front calipers will bolt on with sportivo discs as a starting point. To have somewhere like Tunehouse do the work you'll want to budget somewhere between 20-40K
      CHA54 in Corolla / Corolla Sportivo Club
    8. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      I did the mathematics myself regarding costs vs benefits for fuel injector cleaner. I have changed from 91ULP to 95PULP and 98PULP. Price difference can be about 13 -20 cents. Compared to 91ULP, Premium quality fuel should have a better quality additive package designed to have superior engine cleaning capabilities so the engine can perform at their best.
      campbeam in Camry Club
    9. 3

      Camry Touring 2010 Fuel consumption 15.2L/100km. Normal?

      "Fuel injector cleaner is a waste of money" Only if you by the cheap crap if you use LiquMolly a German Product it does work and you won't waste your Money.
      Aussie Camry in Camry Club
    10. 0

      Camry Touring 2010 A/C Issues.

      Hi Guys, My Camry 2010 Touring just had a regas done on it and the next day for some reason it wasn't blowing cold air but the next day it is and now working with nice cold air BUT every now and then we can hear and feel a buzz for a few secounds and today while my sister took my car I could her like a mild knocking sound when stopped but goes away when driving off. Any idea what this could be and the A/C is always working now for now.
      Aussie Camry in Camry Club
×
×
  • Create New...

Forums

News

Membership