Jump to content


What did you do to your car today?


Recommended Posts

After a week or so of planning with a mate who had the appropriate skills and a quick phone call to another mate who had the appropriate equipment - the problem was resolved. Now that the filter was sticking out of the bonnet, I need to ensure that it was adequately and securely covered so as to avoid any problems with the boys in blue - with a WRX bonnet scoop... At the end of it all a couple of celebratory rums were had, and my mate and I appreciated a job well done.

266601_10150224158122396_709232395_7627108_4439712_o.jpg

280265_10150224158562396_709232395_7627112_2288499_o.jpg

266612_10150224159102396_709232395_7627117_2844328_o.jpg

272696_10150224165907396_709232395_7627247_2091979_o.jpg

279588_10150224160127396_709232395_7627132_2886512_o.jpg

279560_10150224160837396_709232395_7627141_6286574_o.jpg

266645_10150224167302396_709232395_7627265_6696716_o.jpg

266545_10150224168337396_709232395_7627278_1694034_o.jpg

Next on the list are a set of universal coil overs to lower it, front mounted spot lights, and sanding down and respraying the bottom section of the car to give it a yellow and black 2 tone effect... Will keep you all updated :)

Link to comment
Share on other sites


Just removed the Tail-light from the ZRE, was quite a challenge as it was my first attempt. Pulled all of the interior trim out as it was difficult to access the plastic clips. I finally got the light out and started draining the copious amounts of water. I actually collected the water and measured 450ml of water. I didn't want to have to unseal it and re-seal it, so I just let the sun evaporate as much as possible, then I put the tail light back in place. Stupid car not being under warranty.

Link to comment
Share on other sites

Midnight mechanics were back in business tonight fitting some shiny new RDA slotted front rotors. Bye-bye warped rotor vibration, hello barely noticable increase in braking performance! :yahoo:

Link to comment
Share on other sites

I ****** my rim driving into the work car park.

It is around 8cm and on the Chrome Lip. Picture attached.

Someone is going to pay for it with blood, **** assholes make the entrance so narrow.

post-14100-0-46073200-1310598105_thumb.j

Link to comment
Share on other sites

80000km service done today. Replaced in-tank fuel filter (thanks KenshinX for the tutorial, helped A L O T), replaced front brake pads, replaced front wiper blades, topped up various fluids, checked brake fluid (all gud). Need to replace the battery though. All up, good service

Link to comment
Share on other sites

whilst waiting for bits and pieces for the corolla to arrive I test fitted some universal coilovers on the sherpa and the new watanabe (knock offs) that I bought for it... Uber annoyed because the wheel studs are too short so now I have to find a set of WRX wheel studs to accommodate my wheels... :(

Today I'm hoping to have them cleaned and either painted or ready to be painted tomorrow... and hopefully I'll find a set of wheel studs somewhere today - which would be nice...

also purchased a set of Rays super expensive wheel nuts on eBay for $12.00... hahaha

Link to comment
Share on other sites

Just had her weekly bath...now the dragon inlaw is here for lunch :(

mtw46w.jpg

I'm guessing she isn't on the forum? :lol:

Nice pic Lee, car looks hot,BUT I think it needs a front lip,not a big spoiler, just a subtle looking lip,don't know what's out there for it but must be something..

Link to comment
Share on other sites

Thanks Pete

Thanks John...hey mate your known for finding stuff,help a brother out and find me a front lip :D

http://******.blogspot.com/2011/03/universal-front-bumper-lip-splitter.html

i got that, just waiting to the bumper to come in and be painted before i install it,

i reckon it looks pretty good imo havent seen what it looks like on the camry yet though *stupid car accident <_< *

Link to comment
Share on other sites

This is not 'What I did to my car today' but more 'what I got for m car today'

http://cgi.ebay.com/ebaymotors/1976-toyota-celica-liftback-gt-grille-/220813191970?pt=Motors_Car_Truck_Parts_Accessories&hash=item33697deb22

I feel a bit bad for the guy selling but I did put in a stating bid of $120.00. He quoted me just under $50.00 postage and has said he will send it as soon as the PayPal transfer clears.

I also bid $4000.00 on a project 28 near Ipswich but the guy who got it must have really wanted it. :angry: I believe it had been smashed on the passenger side front which made the hood alignment out by about 15mm on the left side. But with the 18R-G and a rust free body I am sure it wont be a real problem to get back on the road.

http://offer.ebay.com.au/ws/eBayISAPI.dll?ViewBids&_trksid=p4340.l2565&item=260815656309

If it was anyone here congrats on the great buy.

P.S. And how far were you prepared to go???

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.





  • Join The Club

    Join the Toyota Owners Club and be part of the Community. It's FREE!

  • Latest Postings

    1. 17

      Wobble at the front

    2. 7

      Brake issues

    3. 10

      Best Oil for 2014 Lancruiser GXL 200 series TT V8 Diesel

    4. 25

      RADIO CODES "HELP"

    5. 17

      Wobble at the front

    6. 11

      rear wheel arch hole covers (3rd row seats removed)

    7. 1

      2013 Kluger grande Bluetooth music issues

    8. 0

      2010 MANUAL Prado with high speed acceleration hickup

    9. 10

      Best Oil for 2014 Lancruiser GXL 200 series TT V8 Diesel

    10. 1

      2013 Kluger grande Bluetooth music issues

×
×
  • Create New...

Forums


News


Membership